说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 中压内缸
1)  IP inner casing
中压内缸
1.
This paper presents the configuration of IP inner casing of steam turbine in combined cycle power plant with SIEMENS V94.
3A重型燃机联合循环汽轮机中压内缸的结构特点,详细阐述了联合循环汽轮机中压内缸的工艺攻关过程,解决了中压内缸国产化制造中的难点,对类似结构的SIEMENS产品的国产化制造具有借鉴意义。
2)  high-intermediate pressure inner cylinder
高中压内缸
1.
The article introduces and compares different treatment methods to the problem of high-intermediate pressure inner cylinder distortion of No.
对浙能兰溪电厂1号、2号机组高中压内缸变形问题的不同处理方法作了介绍和对比,总结了处理类似问题的方法。
3)  cylinder pressure
缸内压力
1.
Based on an experimental study conducted on a single-point injection CNG engine,various approaches for analyzing cycle-by-cycle variation in spark ignition engine were investigated through the measured cylinder pressure and heat release rate curve.
通过单点电喷天然气发动机上的实验研究,分析了利用实测缸内压力和放热率曲线来分析研究点火发动机循环变动的各种方法,并阐述了各种方法的适用性以及不同表征循环变动的参数之间的关系。
2.
Frequency domain analysis of the averaged signal shows that the cylinder pressure signal can contain the primary interesting information only if it preserves the first 50 orders harmonic components of the crankshaft rotation.
在不同的燃烧状况下同时测量缸盖表面振动信号和缸内压力信号,对平均处理后的信号进行频域分析,发现缸内压力信号中相对于基频前50阶的谐波分量包含了所关心的主要信息。
4)  in-cylinder pressure
缸内压力
1.
An equivalent leaking orifice area was calculated according to the measured in-cylinder pressure versus time curves during the compression-combustion-expansion processes,and then the blo.
作者利用已知的缸内压力-时间关系曲线,对活塞的有效漏气面积进行了计算,在根据燃烧时缸内压力变化关系曲线对燃烧缸的漏气量进行了计算。
5)  LP inner casing
低压内缸
1.
Based on the testing results, the damaged area of ductile iron LP inner casing of 900MW supercritical steam turbine is repaired successfully.
 叙述了QT400 15球墨铸铁可焊性试验评定及应用举例,试验包括检测QT400 15焊接接头的抗裂性、抗拉强度、金相分析及接头残余应力水平的评估等,并将试验结果成功应用于超临界900MW汽轮机球墨铸铁低压内缸的修复。
6)  high pressure inner cylinder
高压内缸
1.
This dissertation discussed radial rub from two reasons which caused radial rub, calculated the distortional tendency and distortional quantity of the high pressure inner cylinder in different operation conditions, presented the writer’s standpoint about the distortion and expounded the reason of the distortion.
使用有限元软件计算了高压内缸在各个工况下的变形趋势和变形量,提出了本文的变形观点,并详细阐述了变形原因;采集振动信号,分析了发生径向碰磨后缸体和转子振动信号的特征,并开发了汽轮机组碰磨监测诊断系统。
2.
Based on the 300MW unit, calculations of high pressure inner cylinder on different typical conditions are carried out, and the deformation trends are concluded.
以300MW汽轮机组为对象,对高压内缸进行几种典型工况的分析计算,得出了高压内缸在不同工况下的径向变形趋势并分析了变形原因。
补充资料:辅助压缸
分子式:
CAS号:

性质:在采用油压缸的液压机、注塑机、传递模塑机等的合模机构中,为缩短合模时间而设的辅助油缸。其截面积较小,故不大的液压油流量就可提供较大的合模速度。模具到位后,主合模油缸充油,才产生高的锁模力。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条