1) LY12 aluminum
LY12铝
1.
Experimental study of light reflectivity of the shocked LY12 aluminum unloading to different gases;
冲击压缩LY12铝向不同充气介质卸载后的光反射率实验研究
2.
LY12 aluminum spherical projectiles are loaded by two stage light gas gun,using sweep Langmuir probe diagnostic system designed to measure plasma.
通过二级轻气炮加载LY12球形铝弹丸,采用设计的扫描Langmuir探针诊断系统分别进行了入射角度(与靶板水平面的夹角)为45°,60°和90°条件下碰撞LY12铝靶产生等离子体的实验诊断。
3.
The experimental method to measure the high-pressure sound velocity of shock-compressed LY12 aluminum alloy by VISAR technique is described.
介绍了利用VISAR技术测量受冲击压缩LY12铝的高压声速的方法。
2) LY12 aluminum alloy
LY12铝合金
1.
Microstructures and properties of friction stir spot welding joints for LY12 aluminum alloy;
LY12铝合金摩擦点焊接头组织及性能
2.
Temperature dependence of dynamic yield strength and spall strength for LY12 aluminum alloy under shock loading;
冲击加载下LY12铝合金的动态屈服强度和层裂强度与温度的相关性
3.
Mechanism of brazing flux reacting with oxide film of LY12 aluminum alloy;
LY12铝合金氧化膜与钎剂的反应机制
3) LY12 alloy
LY12铝合金
1.
Cavity behavior of LY12 alloy during superplastic deformation;
LY12铝合金在超塑性变形中的空洞行为
2.
Effect of deposition of ammonium chloride and ammonium sulfate on atmospheric corrosion of LY12 alloy;
两种盐沉积对LY12铝合金大气腐蚀行为的影响①
3.
Study of Rare Earth Sealing Anodizd LY12 alloy;
LY12铝合金阳极氧化稀土后处理的研究
4) LY12 aluminium alloy
LY12铝合金
1.
Nano-machining experiment of LY12 aluminium alloy polishing with ice desk;
LY12铝合金的冰盘抛光纳米加工实验研究
2.
plastic strain (εp) curves of LY12 aluminium alloy treated by aging or thermal-cold cycling techniques.
分析了LY12铝合金时效处理及冷热循环处理后的微屈服应力-微塑性应变曲线特征,探讨了尺寸稳定化处理对微屈服行为的影响。
3.
In order to have an insight into the microscale deformation characteristics and failure mechanism of LY12 aluminium alloy processed by laser shot peening(LSP) and laser irradiation(LI),in-situ tensile behavior of the alloy sample was studied by loading machine and observed under scanning electron microscope(SEM)using different power densities laser shot peening and laser irradiation.
为了研究激光冲击喷丸与激光辐照处理后LY12铝合金材料的微尺度变形特点和失效机理,对经过不同激光功率密度处理后的LY12铝合金材料,在扫描电镜下进行了原位拉伸力学行为和失效机理研究。
5) LY12 Al alloy
LY12铝合金
1.
The technology for brazing LY12 Al alloy at middle temperature is realized by improved KF CsF AlF3 flux matching Ag Al Cu Zn filler metal.
采用改进的KF -CsF -AlF3 中温无腐蚀钎剂与Ag -Al-Cu -Zn中温钎料实现了对LY12铝合金的中温钎焊 ,钎焊接头的抗剪强度可达到母材强度的 80 % ,对接接头钎缝的抗拉强度可达到母材强度的 70 % ,突破了“热处理强化铝合金通常不能钎焊”的传统论断。
2.
In order to improve the surface properties of LY12 Al alloy,black ceramic coatings were prepared on LY12 Al alloy substrate through the hard anodic oxidation technique in an electrolyte of sulfuric acid solution.
为了提高LY12铝合金的表面性能,在硫酸体系电解液中通过硬质阳极氧化法在LY12铝合金表面制备了黑色陶瓷膜。
6) LY12 duralumin
LY12硬铝
1.
LY12 duralumin was heat treated on a trial basis and the variation of microstructure and mechanical pro-perties with heat treatment process was obtained.
对LY12硬铝合金进行了热处理工艺试验,获得了该合金热处理工艺与力学性能之间的关系。
补充资料：11-Dioxa-5,12-distannahexadecane, 5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-6
CAS：67701-37-5
分子式：C36H74O4Sn2
中文名称：2-辛基丁二酸二(三丁基锡)
英文名称：11-Dioxa-5,12-distannahexadecane, 5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-6
6,11-Dioxa-5,12-distannahexadecane,5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-
分子式：C36H74O4Sn2
中文名称：2-辛基丁二酸二(三丁基锡)
英文名称：11-Dioxa-5,12-distannahexadecane, 5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-6
6,11-Dioxa-5,12-distannahexadecane,5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条