1) LY12 alloy
LY12合金
1.
The LY12 alloy after artificial aging was carried out tensile test at different temperature.
对人工时效后的LY12合金进行了不同温度系列拉伸试验,采用SEM和光镜对断口及其附近的显微组织进行观察,研究了温度对LY12合金拉伸变形行为的影响。
2.
Microplastic deformation behavior of LY12 alloy under several typical heat treatment conditions has been investigated in this work.
研究了LY12合金在多种热处理制度下的微塑变抗力 ,发现退火、淬火态的微塑变抗力很低 ,循环态次之 ,时效态最高。
3.
A deformation resistance model of hot rolling was constructed by a FORTRAN regression program, on the basis of which, the multipass hot rolling reduction schedule of LY12 alloy is programmed by QBASIC language.
采用FORTRAN程序建立了LY12合金热轧变形抗力模型，在此基础上用QBASIC语言编制了该合金多道次热轧压下规程电算程序。
2) LY12 aluminum alloy
LY12铝合金
1.
Microstructures and properties of friction stir spot welding joints for LY12 aluminum alloy;
LY12铝合金摩擦点焊接头组织及性能
2.
Temperature dependence of dynamic yield strength and spall strength for LY12 aluminum alloy under shock loading;
冲击加载下LY12铝合金的动态屈服强度和层裂强度与温度的相关性
3.
Mechanism of brazing flux reacting with oxide film of LY12 aluminum alloy;
LY12铝合金氧化膜与钎剂的反应机制
3) LY12 alloy
LY12铝合金
1.
Cavity behavior of LY12 alloy during superplastic deformation;
LY12铝合金在超塑性变形中的空洞行为
2.
Effect of deposition of ammonium chloride and ammonium sulfate on atmospheric corrosion of LY12 alloy;
两种盐沉积对LY12铝合金大气腐蚀行为的影响①
3.
Study of Rare Earth Sealing Anodizd LY12 alloy;
LY12铝合金阳极氧化稀土后处理的研究
4) LY12 aluminium alloy
LY12铝合金
1.
Nano-machining experiment of LY12 aluminium alloy polishing with ice desk;
LY12铝合金的冰盘抛光纳米加工实验研究
2.
plastic strain (εp) curves of LY12 aluminium alloy treated by aging or thermal-cold cycling techniques.
分析了LY12铝合金时效处理及冷热循环处理后的微屈服应力-微塑性应变曲线特征,探讨了尺寸稳定化处理对微屈服行为的影响。
3.
In order to have an insight into the microscale deformation characteristics and failure mechanism of LY12 aluminium alloy processed by laser shot peening(LSP) and laser irradiation(LI),in-situ tensile behavior of the alloy sample was studied by loading machine and observed under scanning electron microscope(SEM)using different power densities laser shot peening and laser irradiation.
为了研究激光冲击喷丸与激光辐照处理后LY12铝合金材料的微尺度变形特点和失效机理,对经过不同激光功率密度处理后的LY12铝合金材料,在扫描电镜下进行了原位拉伸力学行为和失效机理研究。
5) LY12 Al alloy
LY12铝合金
1.
The technology for brazing LY12 Al alloy at middle temperature is realized by improved KF CsF AlF3 flux matching Ag Al Cu Zn filler metal.
采用改进的KF -CsF -AlF3 中温无腐蚀钎剂与Ag -Al-Cu -Zn中温钎料实现了对LY12铝合金的中温钎焊 ,钎焊接头的抗剪强度可达到母材强度的 80 % ,对接接头钎缝的抗拉强度可达到母材强度的 70 % ,突破了“热处理强化铝合金通常不能钎焊”的传统论断。
2.
In order to improve the surface properties of LY12 Al alloy,black ceramic coatings were prepared on LY12 Al alloy substrate through the hard anodic oxidation technique in an electrolyte of sulfuric acid solution.
为了提高LY12铝合金的表面性能,在硫酸体系电解液中通过硬质阳极氧化法在LY12铝合金表面制备了黑色陶瓷膜。
6) LY12-CZ aluminum alloy
LY12-CZ铝合金
补充资料：11-Dioxa-5,12-distannahexadecane, 5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-6
CAS：67701-37-5
分子式：C36H74O4Sn2
中文名称：2-辛基丁二酸二(三丁基锡)
英文名称：11-Dioxa-5,12-distannahexadecane, 5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-6
6,11-Dioxa-5,12-distannahexadecane,5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-
分子式：C36H74O4Sn2
中文名称：2-辛基丁二酸二(三丁基锡)
英文名称：11-Dioxa-5,12-distannahexadecane, 5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-6
6,11-Dioxa-5,12-distannahexadecane,5,5,12,12-tetrabutyl-8-octyl-7,10-dioxo-
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条