1)  low strain dynamic testing
小应变测试
2)  minimum stress
最小应力
1.
This paper firstly designs the parameters for minimum stress of series resonant capacitor charging power supply.
为此,先后对串联谐振电容充电电源进行了最小应力设计,对后级共振充电电源进行了分析与设计。
3)  small strain
小应变
1.
Effect of stress path circumgyration on shear modulus under small strain and initial stress state;
小应变原岩状态下应力路径旋转对剪切模量的影响
2.
Summary and evaluation of experimental investigation on small strain of soil;
土体小应变试验研究综述与评价
3.
Experimental study on constitutive model of sandy soil with consideration of stress path at small strain;
砂土在小应变下考虑应力路径影响的本构模型的试验研究
4)  small strain method
小应变法
1.
This paper discussed the basic problem on bearing capacity of pile estimated by small strain method of dynamic testing,and introduced simply the techniques and features in the analogy simulation theory and tests of pile engineering.
讨论了小应变法动测桩承载力的基本问题 ,简述了类比模拟理论及工程试验中的类比模拟手法与特点 ,探讨了类比模拟法应用于研究小应变法动测桩极限承载力的可行性 类比模拟 ,作为一种思维方法 ,可起着一种解放人们被束缚着的思想观念的作用 ;作为一种技术手段 ,它可以使人们借鉴与积累经验 实例分析的结果表明 ,动测刚度可直接用以推测桩的极限承载
5)  small strain
微小应变
1.
Deformation characteristics of rockfill at small strains;
微小应变下堆石料的变形特性
2.
A new kind of automatic precision test system of triaxial compression is introduced in this paper, then the relationships between stress and strain of soft rock are revealed from the tests by the above test system under the condition of small strain (below e_1=10~(-5) strain level) and the elastic modulus of soft rock can be obtained.
本文首先介绍一种岩土自动化精密三轴压缩试验系统,并以此试验系统所得的一组实验结果为例,揭示软岩在微小应变(ε_1=10~(-2)—10~(-5))条件下所反应的应力-应变的线性关系,以及根据软岩在弹性范围内所测得的数据求出弹性模量。
6)  small strain
“小应变”
1.
At present,it is a dispute problem that the small strain method of dynamicaldetermination for single Pile if can be used on the axial bearing capacity.
本文讨论了当前动力测桩中“小应变”法能否应用于确定单桩轴向承载力这一有争议的问题。
参考词条
补充资料:测试结果可接受性的检查和最终测试结果的确定


测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result

  C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。