说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 碰撞振动
1)  vibro-impact
碰撞振动
1.
Feedback control of a vibro-impact system by states prediction;
碰撞振动系统的状态预测反馈控制
2.
Symmetry of the Poincaré map and bifurcations of a two-degree-of-freedom vibro-impact system;
两自由度碰撞振动系统的Poincaré映射的对称性及分岔
3.
Spectral analysis of Lyapunov exponents for a two-degree-of-freedom vibro-impact system
两自由度碰撞振动系统的Lyapunov指数谱分析
2)  vibro impact
碰撞振动
1.
The theory obtained herein is applicable not only to period doubling bifurcation and Hopf bifurcation of multi parameter vibro impact systems with two degree of freedom, but also to those of the other dynamic systems which can be described as four dimension mapping systems.
其理论结果可以应用于确定含多参数的两自由度碰撞振动系统的周期倍化分叉和 Hopf分叉的分叉参数临界值。
2.
Hopf bifurcation of a two degree of freedom vibro impact system in a strong resonance case is investigated by theoretical analysis and numerical simulations.
采用理论分析和数值仿真相结合的方法 ,研究了一类两自由度碰撞振动系统在一种强共振条件下的Hopf分叉问题 。
3.
An analysis is presented for determining exact steady state responses for a two degree of freedom vibro impact system in the paper.
提出了研究两自由度碰撞振动系统的周期运动及其稳定性的判别方法,计算了此碰撞振动系统的动态响应,数值算例阐明了该方法的有效
3)  impact vibration
碰撞振动
1.
The method is then applied to a two-degree-of-freedom reciprocating impact vibration system with gap.
首先介绍了该方法的基本原理,然后将该方法用于含间隙往复碰撞振动系统的分叉和混沌异常运动的抑制。
4)  Vibro-lmpact
碰撞-振动
5)  vibroimpact
振动碰撞
1.
A treatment of contact bounce as a free vibroimpact, i.
将电触头弹跳现象作为自由振动碰撞的强非线性或突变问题处理,应用计算机数值模拟获得该问题的理论解,由此发现弹跳过程是无序运动,从理论上揭示了非线性动态接触电阻产生的动力学根源,数值模拟结果表明电接触系统机械设计参数对接触的动态过程有显著的影响。
6)  oblique-impact vibration
斜碰撞振动
1.
This paper studied the oblique-impact vibration of a double compound pendulum with the end displacement limit under harmonic moment excitation.
研究了简偕力矩激励作用下的平面双摆与单侧刚性约束面之间的斜碰撞振动,讨论并推导了系统在斜碰撞前后的状态关系,并用数值方法研究了激励参数和系统物理参数的变化对系统稳态行为的影响,揭示了斜碰撞振动系统的运动复杂性。
补充资料:点振子振动和点电极振子振动
分子式:
CAS号:

性质:又称点振子振动和点电极振子振动。振动能量绝大部分集中在点电极范围内,形成“能量封闭”的振动模式。振子电极面远小于压电陶瓷片的总面积,且与厚度有适宜的匹配关系。在交变电场作用下,沿厚度方向产生振动,其振幅随着至电极中心距离的增加,呈指数式衰减。谐振频率与压电陶瓷片的厚度有关。为提高频率通常将压电陶瓷片磨得很薄,有时考虑到压电陶瓷自身强度太低,可用特制的陶瓷片作垫片来防止压电陶瓷片损坏。常用于高频场合。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条