1) spring-beam method
弹簧-梁单元法
1.
Analysis models of underground structures commonly uses spring-beam method and finite element method.
介绍了采用弹簧-梁单元法建立分析模型的过程以及模型参数的选取,并对工程实例进行内力和变形的计算。
2) spring element
弹簧单元
1.
51 environment, the contacting rigidity between slide block and linear guideway was simulated with spring elements, the finite element model of the machine tool was set up, and the static rigid.
51环境中,用弹簧单元来模拟滑块与直线导轨的接触刚度,建立了机床的有限元模型,并对其静刚度进行了分析。
2.
Spring element was used to simulate main bearing in order to match reality more exactly.
在计算中充分考虑主轴承刚度对曲轴应力的影响,采用弹簧单元模拟轴承支承,更接近实际情况。
3.
Moreover,rotational spring elements and axial spring elements were used in the FEM analysis to simulate the semi-rigidity of joints and the connection stiffness.
采用通用有限元软件ANSYS对试验中的脚手架体系建立三维杆系计算模型,考虑材料的弹塑性及结构的几何非线性,进行非线性极限承载力分析;并引入转角弹簧和轴向弹簧单元分别模拟梁柱节点半刚性以及支撑与节点的连接刚度,通过改变弹簧单元的刚度对整个结构进行参数分析,得到与试验结果较吻合的数值分析模型。
3) Multi-spring Element
多弹簧单元
4) soil spring element
土弹簧单元
5) double spring element
双弹簧单元
1.
The plastic damage cracking model of concrete was used to stimulate the reinforced concrete slab in Satish C Jain experiment by the introduction of the double spring element for stimulating the bond slip interaction between steel bar and concrete.
应用混凝土塑性损伤开裂模型,引入双弹簧单元来模拟钢筋-混凝土的粘结滑移作用,对Satish C Jain试验的钢筋混凝土板进行数值模拟,并将模拟结果与试验结果作了对比。
6) single-spring joint element
单弹簧联结单元
1.
Based on the traditional double-spring joint element method,a new method—single-spring joint element method based on the mixed coordinate system, was proposed for bond-slip problems of steel bars and concrete.
在传统双弹簧联结单元法的基础上,提出了一种求解钢筋与混凝土黏结滑移问题的新方法——基于混合坐标系的单弹簧联结单元法。
补充资料：ANSYS壳单元分析箱梁
! Analysis a box beam section with shell elements of ANSYS
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
! 用ansys的壳体单元分析箱梁
! Box dimension: 10*4*4m with shell thickness of 0.04m
! By Lu Xinzheng, Depart. Civil Engineering, Tsinghua University, Beijing
! 陆新征，清华大学土木系
! Aug. 2004
! Define the Element
! 定义单元
/PREP7
!*
ET,1,SHELL93
!*
! Define the section for shells
! 定义壳单元截面
R,1,.04, , , , , ,
!*
! Define the material
! 定义材料
MPTEMP,,,,,,,,
MPTEMP,1,0
MPDATA,EX,1,,200e9
MPDATA,PRXY,1,,.3
! Setup the model
! 建模
! Define the keypoints
! 定义关键点
k,1,0,0,0
k,2,4,0,0
k,3,4,4,0
k,4,0,4,0
! Define the lines
! 定义线
l,1,2
l,2,3
l,3,4
l,4,1
! Define the section area
! 定义截面
a,1,2,3,4
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条