1) low temperature burning
低温烧制
2) low temperature sintering
低温烧结
1.
In situ synthesis of Al matrix composite reinforced with micron-Al_2O_3 particles by low temperature sintering;
低温烧结原位合成微米级Al_2O_3颗粒强化Al基复合材料
2.
The effects of SiO2 on the properties of low temperature sintering lead antimony-manganese zirconate titanate Pb(Mn1/3Sb2/3)0.
探讨了低温烧结时SiO2掺杂对锑锰锆钛酸铅Pb(Mn1/3Sb2/3)0。
3.
The low temperature sintering technology of boron carbide ceramics is summarized, stating granularity.
综述了各种碳化硼陶瓷低温烧结技术及其影响因素,阐述了粉末粒度、制备工艺和化学成分等关键因素对碳化硼陶瓷烧结温度的影响,分析了进一步降低碳化硼陶瓷烧结温度的可能途径。
3) Low-temperature sintering
低温烧结
1.
Research on low-temperature sintering of AlN ceramics;
氮化铝陶瓷的低温烧结研究
2.
Effect of combined additives on low-temperature sintering of AlN ceramics;
复合助剂对氮化铝陶瓷低温烧结的影响
3.
The application of low-temperature sintering technology to the 90/105m~2 sintering machine of Angang;
低温烧结在安钢90/105m~2烧结机上的应用
4) low temperature calcination
低温煅烧
1.
Preparation of BaTiO_3 nanopowders by solid phase grinding-low temperature calcination method;
固相研磨-低温煅烧法制备钛酸钡纳米粉体
2.
Preparation and characterization of barium strontium titanate nanoparticles by low temperature calcination method
钛酸锶钡纳米粒子的低温煅烧法制备与表征
5) low temperature combustion
低温燃烧
1.
05)O(3-δ) powders with homogeneous composition were synthesized via the low temperature combustion process based on the Pechini method.
用柠檬酸及乙二醇作络合剂和燃料,硝酸作氧化剂,氨水作pH值调节搅和燃烧助剂,通过低温燃烧法合成了固体电解质SrCe0。
2.
The concept and background of low temperature combustion(LTC) were introduced,the realizing mode and characteristic of LTC at present were analyzed,and the recent research progress of LTC was described.
介绍了柴油机低温燃烧模式的概念和提出背景,详细分析了其现阶段在柴油机上的实现方式及特点,并且阐述了这种燃烧模式的最新研究进展。
3.
In the concept of low temperature combustion, experimental cycles are made on NOx emission from a 4135G diesel engine by changing injection timing and compression ratio on propeller working condition, according to the IMO Technical Code.
在“低温燃烧”的概念下,根据IMO《船用柴油发动机氮氧化物释放控制技术规则》推荐的试验程序,对一台4135G柴油机在推进工况下进行改变喷油正时和压缩比的试验研究。
6) low-temperature roasting
低温焙烧
1.
by low-temperature roasting,leaching and ion exchange of the spent catalyst,it is possible to produce pure platinum and aluminum polychloride.
废催化剂采用低温焙烧、浸出、离子交换等方法进行处理,可制取纯铂,生产聚合氯化铝产品。
补充资料：910低温印花黏合剂
分子式：
CAS号：
性质：外观为白色乳液。含固量(32±1)％。水稀释性好。可在低温熔烘(100℃左右)交联固化。主要成分是丙烯酸酯类共聚物。适用于棉纯涤、丝绸、亚麻混纺织物的涂料印花。还可用于无纺布和静电植绒等的处理。
CAS号：
性质：外观为白色乳液。含固量(32±1)％。水稀释性好。可在低温熔烘(100℃左右)交联固化。主要成分是丙烯酸酯类共聚物。适用于棉纯涤、丝绸、亚麻混纺织物的涂料印花。还可用于无纺布和静电植绒等的处理。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条