说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 配时设计
1)  timing design
配时设计
2)  signal timing plan
信号配时(控制)设计
3)  Assembly design
装配设计
1.
Realization on assembly design system under agile product development;
敏捷化开发环境下产品装配设计系统的实现
2.
Variation propagation approach for collaborative top-down assembly design
自顶向下协同装配设计中的变动传播方法
3.
Components are divided into assembly level and detail level,and the components at assembly level are regarded as the pre-defined components to be applied in assembly designs.
把零件划分为装配级和详细级,把装配级的零件称为预定义构件,用于装配设计。
4)  formulation design
配方设计
1.
Research on formulation designs in silicon carbide ceramic products;
碳化硅陶瓷磨具配方设计方法的研究
2.
The formulation design and the key performances thereof are focused.
介绍了一种用于彩电机壳涂装的紫外光固化涂料,重点阐述了彩电UV涂料的配方设计思路和关键性能,并讨论了影响UV涂料性能的各个因素。
3.
The formulation design of hybrid fibre for braking friction material by the H Scheffe typical polynomial regression model was presented, regression equation was gained by means of stepwise regression optimization method in SPSS, and the optimum point and value of the objective function was obtained by the complex method of multivariate bounded function.
采用HScheffe典型多项式回归模型进行无石棉制动材料混杂纤维的配方设计,利用SPSS中逐步回归的方法求回归方程,并采用多变量约束函数的复合形法求得目标函数的最优点和最优值。
5)  design of clinker component
配料设计
6)  piping design
配管设计
1.
The Piping design of cold box is introduced.
乙烯冷箱国产化具有显著的社会经济效益,其配管设计从管道布置,应力材料等方面统筹考虑,使国产化冷箱成功投产。
2.
To meet the urgent needs of domestic AEC applications, a self-developed piping design software named as CADPLANT is implemented.
论文工作主要集中在具有自主版权的配管设计软件CADPLANT系统中的工厂建模部分和为工厂漫游设计所作的关键算法方面的研究,具体完成的内容有: ● 提出“五点计算法”,解决了多种布管状态混合作用下管线敷设点位置的计算。
3.
To achieve feasible quality control over pump concrete,we must choose the best piping design,make correct pipeline connection,rigid pump operation,strengthen the management of concrete mixing plant and tighten control over mix blend.
对高墩泵送砼进行切实可行的控制要做到:选择最佳配管设计,正确处理管道连接;严格要求卧泵操作手规范操作;加强混凝土拌和楼管理,严格控制混凝土拌制质量等。
补充资料:流体燃料平衡输配设计


流体燃料平衡输配设计
design of fluid fuel balance and distribution

  1 luti ranliao Pingheng shuPei sheji 流体燃料平衡输配设计(design of fluid fuel balanee and distribution)对煤气的生产与消 耗进行平衡及确定工厂煤气与补充燃料供应方案的设 计。 钢铁厂的高炉、焦炉和转炉既是冶炼设备又是煤 气发生设备。钢铁厂副产煤气有产量大、耗量大、波动 大的特点。合理利用副产煤气可减少工厂一次能源购 入量,改善工厂燃料结构。 流体燃料平衡(亦称煤气平衡)是制订工厂流体然 料供配的基本计划和工厂设计的重要组成部分之一。 冶金工厂煤气设施、补充燃料站均按流体燃料平衡表 确定的数据进行设计计算。 流体燃料平衡输配设计的内容包括根据流体燃料 特性与用户特性编制平衡表,以确定合理利用副产煤 气的措施,确定煤气柜与煤气混合加压设施的项目与 规模(见煤气拒设计、煤气混合加压设施设计),进行 煤气管道、煤气调度、防护急救等设施设计。 常用流体燃料冶金过程副产高炉煤气(BFG)、 焦炉煤气(C OG)、转炉煤气(Ll洲3),少数工厂也副 产电炉煤气和(或)铁合金炉煤气。补充流体燃料常用 燃料油、天然气(NG)、发生炉煤气、水煤气与液化石 油气(LPG)等。常用煤气特性示于表1。 表1常用煤气的典型成分与热值(低发热t)象卜寸一… 常用的燃料油有渣油或重油,需加热保温才有较用户特性高炉副产高炉煤气,高炉热风炉系用好的流动性,热值为418ookJ/kg左右。液化石油气在高炉煤气加热,其消耗的高炉煤气的热量约占高炉煤压力状态下呈液体,减压时气化,热值约为4598okJ/气总热量的40%~45%。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条