1) junction temperature
结温
1.
A new non-contact method based on relative radiation intensity for determining junction temperature of LEDs
基于相对辐射强度的非接触式LED结温测量法
2.
Measurements of LEDs Spectral Characteristics and Junction Temperature
LED结温与光谱特性关系的测量
3.
Based on the analysis of the relationship between maximum fault current and junction temperature of HVDC thyristor, atransient thermal impedance is built, an optimum arithmetic of thyristor s temperature rising calculation is proposed, and computer simulationis carried out.
在分析HVDC晶闸管最大故障电流与结温关系的基础上,建立瞬态热阻抗模型,提出了一种计算晶闸管温升的优化算法,并进行了仿真计算。
2) PN junction temperature
PN结结温
3) Sintering Temperature
烧结温度
1.
Effects of sintering temperature on fatigue damage of alumina ceramics;
烧结温度对氧化铝陶瓷疲劳损伤过程的影响
2.
Effect of sintering temperature on contexture and performance of iron-based P/M aircraft brake materials;
烧结温度对铁基粉末冶金航空刹车材料组织的影响
3.
Effect of sintering temperature on microstructure and mechanical property of ceramic corundum abrasives;
烧结温度对陶瓷刚玉磨料性能的影响
4) low temperature sintering
低温烧结
1.
In situ synthesis of Al matrix composite reinforced with micron-Al_2O_3 particles by low temperature sintering;
低温烧结原位合成微米级Al_2O_3颗粒强化Al基复合材料
2.
The effects of SiO2 on the properties of low temperature sintering lead antimony-manganese zirconate titanate Pb(Mn1/3Sb2/3)0.
探讨了低温烧结时SiO2掺杂对锑锰锆钛酸铅Pb(Mn1/3Sb2/3)0。
3.
The low temperature sintering technology of boron carbide ceramics is summarized, stating granularity.
综述了各种碳化硼陶瓷低温烧结技术及其影响因素,阐述了粉末粒度、制备工艺和化学成分等关键因素对碳化硼陶瓷烧结温度的影响,分析了进一步降低碳化硼陶瓷烧结温度的可能途径。
5) Low-temperature sintering
低温烧结
1.
Research on low-temperature sintering of AlN ceramics;
氮化铝陶瓷的低温烧结研究
2.
Effect of combined additives on low-temperature sintering of AlN ceramics;
复合助剂对氮化铝陶瓷低温烧结的影响
3.
The application of low-temperature sintering technology to the 90/105m~2 sintering machine of Angang;
低温烧结在安钢90/105m~2烧结机上的应用
6) high temperature sintering
高温烧结
1.
The post-processing of indirect SLS includes debinding, pre-sintering, high temperature sintering and metal infiltration.
间接法选择性激光烧结技术制备金属件的后处理工艺包括脱脂、预烧结、高温烧结以及渗金属。
2.
WC dispersion strengthened copper (DSC) was prepared by mechanical alloying (MA) in combination with high temperature sintering.
利用机械合金化与高温烧结方法制备WC弥散强化铜材料 ,研究了高温烧结温度和烧结时间对复合材料组织和性能的影响。
3.
Formation and influential factors of high temperature sintering in titanium sponge production by magnesium reduction method were analyzed.
论述了镁法海绵钛生产过程中高温烧结的形成及其影响因素,分析了减少高温烧结的控制措施。
补充资料：p-n结温度计
p-n结温度计
p-n junction thermometer
P·n结温度计(p一n junetion thermome-ter)利用p一n结正向压降随温度变化的特性进行测温的仪器。当通过p一n结的电流恒定时，温度越高p一n结的正向压降愈大。在一定温度范围内，p一n结电压随温度变化的特性近似直线，约为ZmV/℃，非线性误差可小于士0.2℃。把p一n结作成针状、柱状、片状等各种测温头，即可制成测点温、表面温度等的各种温度计。它的线路结构简单，易于制作，发展较快，但由于p一n结性能一致性不理想，作成多测头仪器的精度不高。(李阳望)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条