1) Elastic penetration
弹性压缩量
2) compression elastic modulus
压缩弹性模量
1.
The curing behavior,mechanical properties,compression elastic modulus and dynamic mechanical properties of CR/SBR blends were investigated.
探讨了氯丁橡胶(CR)/丁苯橡胶(SBR)共混胶料的硫化特性,共混硫化胶的力学性能、压缩弹性模量和动态力学性能。
3) compression elasticity
压缩弹性
1.
Thus it has the better heat insulation,higher compression elasticity,higher water vapor permeability and other properties.
经实验测试和部队穿着使用,保暖效果比较好,透气透湿和压缩弹性较高,能够较好满足鞋靴类及服装类产品的实际需求。
2.
The thermal property,bulkiness and compression elasticity were tested according to relevant standards,and the relations between the tested properties and the content of kapok fiber,down and down fiber in the wadding were investigated.
利用自主开发的专利技术制作了木棉/羽绒/羽绒飞丝的混纤系列絮料,参照有关标准测试了其保暖性、蓬松性、压缩弹性,分析研究了这些性能与木棉质量分数、羽绒及羽绒飞丝质量分数之间的关系,得出如下结论:木棉质量分数越高絮料的保暖性能越好;3种纤维的压缩弹性优劣排序为:羽绒>羽绒飞丝>木棉。
4) elastic compression
弹性压缩
1.
In this paper,a method is given for reducing the prestress loss caused by elastic compression of concrete by using the recoverable property of elastic deformation.
根据弹性变形的可恢复特性,提出一种利用临时预应力钢束放松时产生的弹性恢复变形,来减小由于混凝土弹性压缩引起的预应力损失的方法。
2.
This paper briefly introduces the work principles of double prestressed concrete members and gives the calculation method of stress loss of post tensioned double prestressed concrete members caused by the elastic compression of concrete under a simple support condition.
简要叙述了双预应力混凝土构件的工作原理 ,并导出了简支状态下后压法双预应力混凝土构件由于混凝土弹性压缩引起的应力损失的计算方法。
3.
By theoretic analysis, using the prestressed bers which are extra primary stretched by portable jack, the cast-in-site frame affects little on the elastic compression if without consideration of column restriction.
经理论分析，提出采用便携式千斤顶一次超张拉预应力筋，得出现浇框架不考虑柱子约束对弹性压缩的影响较小，还得出预应力筋摩擦系数与张拉应力之间的关系，经工程实践进一步得到了验
5) elasto-plastic compression
桩身弹塑性压缩量
6) spring camber
弹簧压缩量
补充资料：表观弹性模量
分子式：
CAS号：
性质： 在减震橡胶制品中，由于橡胶与金属黏着界面的形状效应，不能仅由形状尺寸和橡胶的弹性模量来决定不同方向的弹簧常数，为此将表观弹性模量Eap定义为：圆柱形：Eap=(3+4.9355S2)G正方形：Eap=(3+6.580S2)G无限长柱：Eap=(4+3.290S2)G式中G为剪切弹性模量，S为形状因子。
CAS号：
性质： 在减震橡胶制品中，由于橡胶与金属黏着界面的形状效应，不能仅由形状尺寸和橡胶的弹性模量来决定不同方向的弹簧常数，为此将表观弹性模量Eap定义为：圆柱形：Eap=(3+4.9355S2)G正方形：Eap=(3+6.580S2)G无限长柱：Eap=(4+3.290S2)G式中G为剪切弹性模量，S为形状因子。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条