1) compensation
偏移补偿
2) eccentric traveling distance
偏移补偿量
1.
According to analysis and calculation for center path of electrode-wire on WEDM,is determined correct eccentric traveling distance,to be improved machining accuracy for punching & blanking die in this paper.
通过电极丝中心运动轨迹的分析与计算,确定其合理的偏移补偿量,以提高冲裁模具的加工精度。
3) migration compensatory algorithm
偏移补偿算法
4) Offset Compensation
电位偏移补偿
5) Migration
偏移
1.
Globally optimized Fourier finite-difference migration in offset domain.;
炮检距域全局优化傅里叶有限差分偏移
2.
Ground penetrating radar data imaging via the 2D finite-diffrence migration method;
2D有限差分偏移技术在探地雷达信号成像中的应用
3.
Magneto-electrotelluric full frequency segment migration imaging technique and its application;
大地电磁全频段偏移成像技术及其应用
6) offset
偏移
1.
Application of the offset analysis in aluminum electrolysis control;
铝电解控制中偏移分析的应用
2.
From the point of view of the error compensation, the lateral offset error compensation of the sub-reflector is discussed and calculated by applying the best re-pointing technique.
建立40m口径天线结构的有限元分析模型,依据有限元分析结果,对副面和馈源偏离理想位置的偏移量和偏移误差进行分析与计算;从误差补偿角度,运用最佳指向技术对副面横偏误差进行补偿分析计算。
3.
Based on solved the non-liner equations with Monte-Carlo method,this paper have a analysis in the error of the phase shifts when it have some offset of the main beam in antenna pattern and have a group of results of the errors.
文中在运用蒙特卡罗方法求解非线性方程组的基础上,对天线的主波束在一定的偏移下各个移相器取值的误差进行了分析。
参考词条
补充资料：创建偏移剖面
要创建偏移剖面，必须通过在“草绘器”中进行草绘以定义切口轮廓。然后，垂直于草绘平面投影此轮廓。单击 
或“视图”(View)>“视图管理器”(View Manager)。“视图管理器”(View Manager) 对话框打开。单击“剖截面”(Xsec)。单击“新建”(New)。出现一个缺省的剖面名称。按 ENTER 键。“剖截面创建”(XSEC CREATE) 菜单打开。单击“偏移”(Offset)>“一侧”(One Side) 或“双侧”(Both Sides)>“完成”(Done)。“选取”(SELECT) 对话框打开。选取草绘平面，并定义查看方向和草绘方向。进入“草绘器”。选取用于尺寸标注的参照图元。草绘剖面轮廓并单击 
退出“草绘器”。 在“视图管理器”(View Manager) 中，单击“显示”(Display)>“设置可见性”(Set Visible)。“可见性”(Visibility) 对话框打开。单击“显示剖面线”(Show X-Hatching) 查看剖面。单击 预览或单击 接受选取的选项。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。