1)  hot pressing
热压制备
2)  hot-pressing
热压
1.
Research and Development of Measuring System for Wood-based Panel Hot-pressing;
人造板热压参数检测系统的研究与开发
2.
Study of hot-pressing process and microstructure of Nd-Fe-B alloy;
钕铁硼粉末热压成型工艺与组织研究
3.
The effect of density on the temperature distribution of particleboard during hot-pressing;
密度对刨花板热压过程中温度场的影响
3)  hot pressing
热压
1.
Effects on synthesis of Ti_2AlC/Ti_3AlC_2 doped with Si from elemental powders by hot pressing and theoretical analysis;
掺Si对热压合成Ti_2AlC/Ti_3AlC_2的影响及理论分析
2.
Microstructure and properties of Nb/NbCr_2 composites prepared by mechanical alloying followed by hot pressing;
机械合金化-热压制备Nb/NbCr_2复合材料的组织与性能
3.
Effect of hot pressing time on microstructure and properties of laves phase Cr_2Nb alloy;
热压时间对Laves相Cr_2Nb合金组织与性能的影响
4)  hot press
热压
1.
Fabrication of tungsten/copper functionally gradient materials with nearly full density by hot press;
热压烧结制备近全致密W-Cu梯度热沉材料
2.
Self-reinforced silicon nitride ceramic was prepared by hot press sintering technique using Y2O3 and La2O3 as sintering aids.
采用Y2O3和La2O3为烧结助剂,利用热压烧结法制备自增韧氮化硅陶瓷,通过L9(34)正交实验,优化各工艺参数并确定各因素的影响序列,研究结果表明:在该体系中,晶种作用不显著;保温时间的影响最大;最佳工艺参数为1820℃、4h、21950N压力及0。
3.
The probability and synthesis conditions of filled skutterudite compounds LayFeCo_3Sb_ 12 by mechanical alloy and hot press using La, Fe, Co and Sb as start powders are studied in this paper, and so is the effect of La filling fraction on thermoelectric properties.
研究以La,Fe,Co及Sb粉末为起始原料,用机械合金化热压法合成填充式Skutterudite化合物LayFeCo3Sb12的可能性和合成条件,研究了La填充分数对LayFeCo3Sb12电性能的影响。
5)  Hot-press
热压
1.
A Mechanism Study on the Technology of Pretreatment of Chalcopyriteby Hot-press Acid Oxidation;
黄铜矿酸性热压预氧化工艺的机理研究
2.
WC-20Co-1Y_2O_3 cemented carbide by hot-press and liquid phase sintering;
热压固结与传统液相烧结对WC-20Co-1Y_2O_3硬质合金组织结构与性能的影响
3.
Study on modification of soy protein isolate hot-pressed;
大豆分离蛋白的热压改性研究
6)  thermal pressure
热压
1.
Coaction of wind pressure and thermal pressure in air infiltration calculation;
空气渗透计算中风压与热压的叠加问题
2.
Calculation of vaporization heat of pure substances by using thermal pressure;
应用热压计算纯物质的汽化热
3.
Theoretical study and CFD prediction of infiltration rate through a cold store entrance under thermal pressure;
三维CFD模型预测热压作用下冷库门的冷风渗透率
参考词条
补充资料：反应热压烧结(reactived hot pressing sintering)
分子式：
CAS号：

性质：又称反应热压烧结(reactived hot pressing sintering)或分解热压烧结(detomposition hot pressing sintering)。利用高温下粉料可能发生某种固相物理化学反应时处于较高能量的活化状态下进行热压烧结的方法。有以下几种类型：(1)相变热压烧结，如利用氧化锆在980～1100℃之间发生相变，同时进行热压，可获得高密度的细晶陶瓷；(2)分解热压烧结，如利用镁或铝的氢氧化物(或其硫酸盐)在高温下(900～1200℃)发生脱水或释气分解时，进行热压，只需加0.3～1MPa压力，保持0.5h，就可获得高密度的制品；(3)分解合成热压烧结，利用分解反应期的高度活性，在压力作用下与异类物质产生反应，然后再在压力作用下烧结成致密陶瓷，如氢氧化钡或碳酸钡分解的氧化钡与二氧化钛合成为钛酸钡等。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。