1) improvement of blender's blades
浆叶设计
2) pouring design
灌浆设计
1.
Discussion on earth and stone dam base curtain pouring design;
土石坝坝基帷幕灌浆设计探讨
3) grouting design
注浆设计
1.
Detailed introduction is made from grouting design,calculation,construction method,matters deserving attention in construction,quality inspection and other aspects.
结合工程概况,提出采用渗透式注浆方式作为加固防护方案,对其注浆设计计算过程、施工工艺、施工注意事项、质量检查等方面进行了介绍,并对其施工效果进行了评价,以供类似工程参考借鉴。
2.
The paper also briefiy introducd drilling and grouting design.
介绍采用地面打钻深孔注浆充填主、副井井壁后空硐,应用了深孔位防偏斜技术,深孔位套管技术等多顶新工艺、新技术,通过浆液高压挤压作用降低孔隙率,减少地层压缩,加固地层,防止井筒的突然破坏,文中对钻孔灌注浆设计进行重点介绍。
3.
This paper introduced the ground pre-grouting design and the key technical measures of construction through an engineering practice, and summarized some useful experiences.
本文通过实例介绍了地面预注浆设计和施工关键技术措施,总结了提高注浆效率、改进“三同时”建井工艺的有益经验。
5) Impeller design
叶轮设计
1.
In order to design a new model centrifugal fan with high performance, a new slotted technique on splitter blade used for impeller design in centrifugal fans was presented.
为高性能新型风机设计进行了应用技术研究，提出在离心风机叶轮设计中采用长短叶片开缝的新技术。
2.
Based on mathematical analyses and centrifugal impeller design principles, which aims at improving the efficiency of the centrifugal pump and shortening the designing period, author of this paper deduces a special method of impeller s meridional drawing, especially the checking method and procedure s formation of F-L curve.
为了提高离心泵的效率，缩短设计周期，本文以数学分析和水泵叶轮设计原理为基础，形成了独特的叶轮轴面投影图的绘制方法，特别是F-L曲线的检查方法和程序的形成，使叶轮轴面投影图的确定更迅速、更准确，能更好的满足不同用户对产品的不同性能的要求。
6) blade design
叶片设计
1.
Three Gorge runner blade designcounted in the effect oflimited blades number;
S_1 流面流动计及有限叶片数影响的三峡转轮叶片设计
2.
New simple and precise blade design model based on the .
本课题以广西教育厅科技项目《1KW风力发电机产品的研究开发》为背景，主要研究小型水平轴风力发电机的叶片设计、性能计算、有限元动力学分析。
3.
Within its process of design, blade design knowledge that I had learned in working p.
0MW叶片的研制为契机,利用自己学习的叶片设计知识,结合单位多年来的叶片设计成果和经验,设计了叶片的外形和结构。
补充资料：搅拌器浆叶和流型
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条