1) steel bracket
钢锚块
2) anchor block
锚块
1.
According to the results calculated by FEM, the effects on stresses with and without the ear of anchor block were compared and discussed, and the different interface modelings between the bottom of anchor block and pier were summarized.
根据计算结果,比较分析了锚块颈部伸出段的安装支座部位(锚块耳朵)去掉前后对锚块和闸墩的受力差异,且讨论了锚块底部与闸墩的3种不同接触方式的模型对计算结果的影响。
2.
Finally,the effect of different interface models between the bottom of anchor block and pier was discussed.
根据有限元计算结果,评价了边墩混凝土结构的预应力效果,并探讨了锚块底部与相应闸墩顶面两种不同接触方式对结果的影响,为结构的设计、施工提供参考依据。
3.
The bearing loads of spillway piers and anchor block of a hydropower station are extremely large;and the maximum thrust of a single radial gate shoe will reach 20 543 kN.
某水电站溢洪道闸墩锚块承受荷载较大,弧门单个支铰处最大水推力达到20 543 kN。
3) steel anchor
钢锚
1.
However, during line constructions, dimensionally mismatches between the shackle clevis and the steel anchor of compression type strain clamp occur frequently, which cause difficulties in installation.
连接电力金具的U形环是按照国标(GB/T2315—2000)规定的尺寸进行加工,在线路施工时,经常会发生U形环挂耳与其连接的压接型耐张线夹钢锚在尺寸上不相配,造成安装困难。
4) anchor steel
锚钢
6) anchor block
锚固块
1.
Strut-and-tie model reinforcement of the external prestressed box-beam anchor block
体外预应力箱梁锚固块拉压杆模型法配筋
2.
A large amount of reinforcing bar mechanical splicing and anchor block have been adopt ed in the reinforcing bar project of the Nuclear Island of Ling ao Nuclear Power Station.
岭澳核电站核岛钢筋工程中,大量采用了钢筋机械接头与锚固块。
补充资料：预应力锚夹具用钢
制作预应力构件用锚夹具的钢材。每一种锚具或夹具都是由几个零件所组成。各零件由于功能要求、冷热加工方法和生产工艺不同，因而所用钢材也各不相同。目前，消耗量最大、用途最广的是中碳钢和中碳低合金钢,其中以优质碳素钢45为主。工作应力较低的零件,是以热轧圆钢直接制成；工作应力较高的零件，则常在冷加工后进行调质处理。夹持式的锚具和夹具中，与预应力筋接触的带齿零件，需要具有更高的表面硬度来提高锚、夹具的锚固性能。所以采用优质碳素钢45和弹簧钢(如65锰等)时，要求用盐液淬火后经低温回火处理；采用低碳或低碳低合金钢(如优质碳素钢15、20或20铬等)、低碳易切削钢（如易20等）时，要求表面渗碳或碳氮共渗。预应力筋强度不高、锚具效率要求不高时，也曾大量使用过铸钢（相当于中国的ZG45）。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条