1) turbine cascade
涡轮叶栅
1.
Upstream wake-passage vortex interaction in turbine cascade;
上游尾迹与涡轮叶栅通道涡相互作用研究
2.
Numerical simulation of the three-dimensional flow field of transonic turbine cascade;
跨声速涡轮叶栅三维流场的数值模拟
3.
Boundary layer transition detection on blade surface in low speed turbine cascade wind tunnel;
低速涡轮叶栅风洞中叶片表面边界层转捩图像捕捉
2) annular turbine cascade
环形涡轮叶栅
1.
An experimental measurement was performed of the three-dimensional average speed in the flow field of an air-cooled annular turbine cascade by using LDV method to study the impact of hole jet flow on the flow field in an annular turbine cascade.
采用LDV对气冷环形涡轮叶栅流场三维平均速度进行实验测量,研究孔射流对环形涡轮叶栅流场的影响。
2.
Four different turbulence models were applied to simulate three-dimensional flow field in annular turbine cascade with film cooling.
采用4种不同的湍流模型对叶片表面带小孔射流的环形涡轮叶栅内部流场进行数值计算,并与热线实验测量结果进行了对比。
3) 3-D turbine blade
三维涡轮叶栅
4) supersonic turbine cascade
超音出口涡轮叶栅
5) turbine wheel
涡轮叶轮
1.
Based on the principle of optimization design,structure optimization of JP60 turbine wheel was carriedout using optimization module of ANSY and APDL in order to obtain minimum turbine weight when retaining.
以车用增压器JP60涡轮叶轮为研究对象,基于最优化设计的原理,在不改变叶型及流道并保证涡轮叶轮结构强度的基础上,利用ANSYS优化设计模块及APDL语言编制用户程序,以涡轮叶轮重量最小为目标对增压器涡轮叶轮进行了减重结构优化。
2.
Taking into consideration the material nonlinearity of turbocharger compressor impellers and turbine wheels,we carry out elastoplasticity numerical analysis of their burst speed based on FEM software ANSYS.
基于ANSYS有限元分析软件,对车用涡轮增压器涡轮叶轮和压气机叶轮进行了材料非线性弹塑性有限元数值分析,计算了涡轮叶轮和压气机叶轮在离心载荷作用下的破裂转速,并与试验结果进行了对比。
3.
Considering material nonlinearity of turbocharger compressor impeller and turbine wheel, Elastoplasticity numerical analysis is carried out for burst speed based on FEM software ANSYS.
基于 ANSYS 有限元分析软件,对车用涡轮增压器涡轮叶轮和压气机叶轮进行了材料非线性弹塑性有限元数值分析,计算了涡轮叶轮和压气机叶轮在离心载荷作用下的破裂转速,并与试验结果进行了对比。
6) vortex-ring cascade
涡流环叶栅
补充资料：常绿阔叶落叶阔叶混交林
出现于亚热带和暖温带的过渡带或亚热带山地常绿阔叶林上界的森林植被类型。由常绿阔叶树和落叶阔叶树混合组成。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条