1) on-line detection
冷态检测法
1.
Finally,the processes and two kinds of methods for seeking power failure,namely on-line detection and off-line detection,are concluded.
探讨了计算机ATX电源的几种常见故障,总结了查找ATX电源故障的步骤,查找电源故障的两种方法:冷态检测法,热态测试法。
2) cold
冷态
1.
0D(D=183 mm),the fluidization velocities are determined in cold bubbling fluidized bed.
0D(D=183 mm,D为有机玻璃管内径)的冷态条件下木屑的流化速度变化情况。
2.
This paper gives a brief introduction of the process of cold commissioning on 135 MW CFB in Xinxiang Thermal Power Plant such as calibration of air meter, measuring of bed resistance, testing of primary air evenness, measuring of minimum fluidized air, testing of slag-colder and slag transport system and also presents a program for U-valve testing.
新乡火电厂135MWCFB锅炉冷态调试过程如风量标定、布风板阻力特性测定、布风均匀性检查、冷态临界流化风量测定、冷渣器及输渣系统试验等,此外还提供了回料阀试验方案供参考。
3.
PM4 CFBB were investigated on a self-made cold CFB experimental set to master the introduced-technology.
在自行研制的循环流化床冷态试验台上对哈锅引进 4 40t/hCFB锅炉关键部件特性及炉内气固流动特性进行了试验研究 ,测定了大直径钟罩式风帽及布风板的阻力特性 ,发现了安装方向对风帽的磨损规律 ,对分叉管U型回料阀和旋风分离器进行了模拟试验 ,对双炉膛结构对流动的影响进行了观察 ,认识了哈锅CFB锅炉的多方面特性。
3) cold state
冷态
1.
Based on the principle of NO X reduction using gas reburning in coal fired boiler, the velocity,temperature and concentration fields of jet are analyzed for single circular cross section nozzle on the condition of cold state by means of the self moulding theory of jet.
以喷气再燃技术降低燃煤锅炉 NOX排放的研究为背景 ,利用射流的自模性理论 ,在冷态下以圆断面射流为例 ,分析了单喷管喷气射流的速度场、温度场和浓度场 ,讨论了影响喷气射流与烟气主流混合的有关因素。
4) cold strength
冷态强度
1.
In this study,the effects of hot briquetting process parameters on cold strength of the CCB,and the mechanism of the CCB high strength are investigated and discussed.
本研究重点考察了煤种及热压工艺参数对热压含碳球团冷态强度的影响,并探讨了热压含碳球团获得高强度的机理。
5) cold modeling
冷态模化
1.
The paper gives an brief analyse about the field of temperature and velocity in a kiln model based on cold modeling calculation,and analyzes the influences on the flow field as correlative parameters such as structure,flow ratio are different.
本文在三通道燃烧器窑内冷态模化计算基础上,进行了窑内速度场、温度场测量,并根据测量数据及计算,分析了几种典型回转窑多通道燃烧器结构参数对窑内流场的影响,通过分析窑内流场空气动力特性,比较了燃烧器不同结构参数对窑内气流混合、燃烧过程及火焰形状的作用,为今后进一步进行新型燃烧器设计提供参考。
6) cold modeling
冷态模拟
1.
Through the experiments of cold modeling,the slag splashing protection technology for 150t BOF in the NO.
通过冷态模拟试验,对唐山钢铁集团有限责任公司第一钢轧厂150 t顶吹转炉的溅渣护炉工艺进行了研究,确定出了最佳操作工艺参数。
参考词条
补充资料：冷态模型试验
分子式：
分子量：
CAS号：
性质：见冷模试验。
分子量：
CAS号：
性质：见冷模试验。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。