1)  Eudragit
丙烯酸树脂
1.
METHODS 4-ASA-Na colon-specific targeting release coated tablets were prepared by a sugar coater,using the acrylic resin Eudragit RL-RS and Eudragit FS as coating polymers,and triethyl citrate as plasticizer.
方法:以渗透型丙烯酸树脂EudragitRL与EudragitRS混和包衣液作为内层缓释层,pH依赖型丙烯酸树脂EudragitFS作为外层肠溶层,以柠檬酸三乙酯作为增塑剂,使用可调速糖衣机包衣,并研究包衣片在模拟人体胃肠道环境中的释放情况。
2.
Results A satisfactory 24 h -sustained release curve can be obtained when the pellets is coated with Eudragit RL30D and RS30D under the optimized formulation and preparing conditions.
结果以丙烯酸树脂EudragitRL30D和EudragitRS30D为包衣材料,质量比为4∶1,包衣增重10 % (w) ,增塑剂的用量为2 0 % (w ) ,无需熟化,可满足2 4h缓释的要求。
3.
Eudragit dispersions were coated as a sustained-release layer in a fluid-bed equipment .
方法采用离心造粒技术制备阿昔洛韦素丸,在流化床内采用丙烯酸树脂水分散体对其包衣,制备阿昔洛韦缓释微丸。
2)  Eudragit
丙烯酸树脂水分散体
1.
Eudragit dispersions were coated as a sustained-release layer in a fluid-bed equipment.
方法采用离心造粒技术制备甲硝唑丸;并在此基础上,在流化床内采用丙烯酸树脂水分散体对其进行包衣,制备甲硝唑缓释微丸。
2.
METHODS Matrine pellets were prepared in a fluid-bed by solution layering and then,coated in a mini fluid-bed by surelease,eudragit or both of them respectively.
方法溶液上药法(流化床底喷装置)制备苦参碱微丸,分别选用乙基纤维素、丙烯酸树脂水分散体及两者同时应用作为包衣材料,采用自制微型流化床进行包衣,分别考察其体外释放度。
3)  Eudragit
Eudragit
1.
Methods The tablet core was compressed with suitable excipients,and the EMT was prepared using film coating technology with Eudragit L100-55.
方法选用适宜的辅料压制莫达非尼片芯,选用Eudragit L100-55为肠溶包衣材料,采用薄膜包衣法制备莫达非尼肠溶片。
2.
METHODS The membranes of Eudragit L100-55 were prepared and investigated,capsules were prepared by a dipping process,in vitro release test was taken and acetaminophen was uesd as the model drug.
方法考察Eudragit L100-55成膜性能,以其作为囊材,使用蘸胶-成膜法制备胶囊壳,采用对乙酰氨基酚作为模型药物,考察体外释放。
4)  Eudragit
优特奇
5)  Eudragit Ⅳ
IV号丙烯酸树脂
6)  Eudragit L100-55
尤特奇L100-55
1.
METHODS:Tα1 was directly compressed to tablet cores and coated with two layers(chitosan hydrochloride and Eudragit L100-55).
方法:将Tα1制成片芯,2次包衣,内层为壳聚糖盐酸盐,外层为尤特奇L100-55。
参考词条
补充资料：丙烯酸树脂
分子式：
CAS号：

性质：丙烯酸和甲基丙烯酸及其酯类或其他衍生物经聚合而成的均聚物和共聚物的总称。具有无色透明、耐光、耐老化的特点。产品性能决定于所用的单体和聚合方法。随聚合方法的不同，产品有固体(分片、板、棒、管、颗粒等形态)、弹性体、油状黏稠液体、溶液和乳液等类型。纯聚产品主要有浇铸聚甲基丙烯酸甲酯(有机玻璃)及其模塑料。溶液树脂和乳液树脂以共聚物为多。用途十分广泛。 

说明：补充资料仅用于学习参考，请勿用于其它任何用途。