1) shaping
[英][ʃeip] [美][ʃep]
塑形
1.
Shaping, placement and fixation of fibula free flap in reconstruction of mandibular defects;
目的 探讨腓骨复合瓣重建下颌骨缺损时骨块的塑形、定位和固定方法。
2) plastic deformation
塑性变形
1.
Effect of particle shape on uniaxial ratcheting of SiC_P/6061Al composites and its microscopic plastic deformation characteristics;
颗粒形状对复合材料单轴棘轮行为及其细观塑性变形特征的影响
2.
Self-healing mechanism of inner crack in plastic deformation under high temperature;
高温塑性变形中孔隙性缺陷自修复机理
3.
Plastic Deformation of a Mg-based Bulk Amorphous Alloy in Supercooled Liquid Region;
镁基大块非晶合金在深过冷液相区的塑性变形
3) plastic forming
塑性变形
1.
The law of the microstructure transformation of SiC p/Al composite based on powder metallurgy in hot plastic forming is investigated.
实验研究了基于 PM的 Si Cp/Al复合材料在热塑性变形过程中显微组织的变化规律。
4) plastic forming
塑性成形
1.
Method of efficient continuous plastic forming for freeform surface part;
自由曲面工件的连续高效塑性成形方法
2.
Experimental studies on plastic forming properties of ME20M magnesium sheet;
ME20M镁合金板料塑性成形性能实验研究
3.
Application research of plastic forming and simulation technology for aluminum alloy thin hemisphere shell;
薄壁铝合金半球壳塑性成形与模拟技术应用研究
5) superplastic deformation
超塑变形
1.
Effect of holding time on high temperature microstructures of hydrogenation TC4 alloy before superplastic deformation;
保温时间对置氢钛合金超塑变形组织的影响
2.
This paper studied the superplastic deformation behavior of enhanced titanium-base composite material in-si- tu autogenesis TiB and TiC under conditions of temperature varied in the range of 920～1080℃ and initial strain rate was 2× 10~(-2)s~(-1)～10~(-4)s~(-1).
研究了温度为920～1080℃、初始应变速率为2×10~(-2)s~(-1)～10~(-4)s~(-1)条件下的原位自生 TiB 和 TiC 增强钛基复合材料的超塑变形行为。
3.
Optical microscope and scanning electronic microscope ( SEM) were employed to observe the microstructure evolution and fracture behavior in superplastic deformation of AZ31 Mg alloy and the values of deformation activation energy at various.
在300-400℃的超塑变形温度范围内,AZ31镁合金超塑变形的主要机制是由晶界扩散控制的晶界滑移,而变形温度和应变速率对AZ31镁合金断裂行为的影响主要体现在变形机制从晶内滑移到晶界滑移的转变。
6) injection molding
注塑成形
1.
By injection molding experiments, shrinkage characteristics of convex, con cave, square and fan-shaped parts are investigated.
设计制作了一套一模四腔的模具(包括正方形、凸形、凹形和扇形等4种形状制品的型腔),通过注塑成形实验,来确定这几种特殊结构制品的收缩特性。
2.
The influence of the different models on the injection molding an alysis is also studied.
目前共有4种分析模型应用于注塑成形CAE系统:1维分析模型;2·5维中面分析模型;2·5维双面网格分析模型;3维实体分析模型。
3.
In this paper,the application and development of artificial neural network(ANN) in injection molding industry and injection molding technology were summarized.
对人工神经网络技术在注塑成形研究中的主要应用和发展概况进行了综述,并将神经网络技术与正交试验设计方法、CAE模拟技术相结合,建立了注塑工艺参数与制品翘曲变形量关系的BP神经网络模型。
补充资料：人物塑形烟壶(清代)
高９厘米。以清代普通官吏的人物造型为壶体，方寸之间营造出形象生动的形象，设计巧妙。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条