2) fatigue test
疲劳试验
1.
Design optimization of fatigue test model for the cable-girder anchorage zone of steel cable-stayed bridges;
斜拉桥索梁锚固结构疲劳试验模型设计优化
2.
Application of non-contact counter in roadways fatigue test;
非接触式计数器在道路疲劳试验中的应用
3.
Performance index and fatigue test of flexible waterproof material on bridge deck;
桥面柔性防水材料的性能指标和疲劳试验
3) Fatigue experiment
疲劳试验
1.
Through study on fatigue experiment to steel reinforced concrete girder pasted with carbon fiber fabric,it shows the fatigue property of the damaged steel reinforced girder is greatly improved,this may prolong the service life of steel reinforced concrete girder,also this provides experiment basis for studying long term fatigue property of carbon fiber fabric steel reinforced concrete structures.
通过对粘贴碳纤维布钢筋混凝土梁的疲劳试验研究,表明粘贴碳纤维布可以较大提高钢筋混凝土梁的疲劳性能,延长钢筋混凝土结构的使用寿命,为碳纤维布加固钢筋混凝土结构的长期疲劳性能研究提供了试验依据。
2.
Based on the data acquired at actual working spot, the fatigue experiment of epoxy asphalt and steel plate conjunction is carried out.
利用有限元方法对某大跨径钢桥面铺装层进行力学分析,以此为依据,现场采样,进行了环氧沥青混合料与钢板的结合件的疲劳试验。
3.
This paper deals with the load-deflection and load displacement curves of beams basedon the fatigue experiments of plated and unplated RC beams.
本文通过钢筋混凝土芯梁及粘贴钢板补强混凝土复合梁的疲劳试验，研究了它们在疲劳试验过程中载荷和加载线位移及跨中挠度的变化规律。
4) fatigue tests
疲劳试验
1.
Research on fatigue tests in the direct track for the asphalt deck pavement of Xiamen Haicang steel bridge;
厦门海沧大桥桥面沥青铺装层直道疲劳试验研究
2.
ing acoustic emission signal on flight stabilizer spindle of fatigue tests,discovered the unconventionality acoustic emission signal and located the location of it.
通过对飞机平尾大轴疲劳试验过程中声发射信号的分析,发现了异常的声发射集中部位,综合分析认为这是由于异常摩擦机制造成的声发射,分析结果得到了卸载目视检查结果的验证。
5) fatigue life
疲劳试验
1.
An experimental study on tensile-tensile fatigue life of interference-fit mechanical joint in composite laminates is presented.
本文对Ｔ３００／ＱＹ８９１１π／４层压板机械连接干涉配合进行了静拉伸挤压和拉－拉疲劳试验。
2.
Through some fatigue tests,the relational curve between the gear fatigue life and lu-bricant viscosity has been obtained.
通过一定的滚子疲劳试验，得出了齿轮疲劳寿命与润滑剂粘度的关系曲线，指出了ＩＳＯ渐开线圆柱齿轮齿面耐久性（点蚀）计算中所引入的润滑系数ＺＬ的不尽合理性。
6) fatigue testing
疲劳试验
1.
Design and simulation of a electro-hydraulic servo 3D loading fatigue testing system for the accessory of a car;
电液伺服三维加载轿车零部件疲劳试验系统设计与仿真
2.
So,based on the rack test methods about fatigue testing of gears in drive-axle assembly of automobile in the QC/T533-1999,this paper brings a new method of design fatigue testing of gears in drive-axle assembly of automobile test bed,and introduce it’s the general structure.
结合汽车驱动桥台架试验方法(QC/T533-1999)中驱动桥总成齿轮疲劳试验方法和要求,提出一种汽车驱动桥总成齿轮疲劳试验的设计方案,介绍了该试验系统的总体结构,并对主要试验台部件作出选择。
3.
This text analyzes the source producing the error of the radial load force of calibration test for the fatigue testing machine, introduces the evaluation method of the uncertain degree of the test result, calculates out the total uncertain degree of the radial load force.
分析车轮径向载荷疲劳试验机校准试验径向加载力产生误差的来源,介绍其不确定度的评定方法,计算出其总的不确定度。
补充资料：ADS疲劳试验
分子式：
CAS号：
性质：考察橡胶裂口增长的一种疲劳试验方法，该法由E. E. Auer、K. W. Doak和I. J. Schaffiner三人首先提出，也由此而得名。试验利用德墨西亚疲劳试验机测定初始割口直径Φ0.93mm在屈挠频率为287次/min下，割口增长和300%定伸应力变化情况。
CAS号：
性质：考察橡胶裂口增长的一种疲劳试验方法，该法由E. E. Auer、K. W. Doak和I. J. Schaffiner三人首先提出，也由此而得名。试验利用德墨西亚疲劳试验机测定初始割口直径Φ0.93mm在屈挠频率为287次/min下，割口增长和300%定伸应力变化情况。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条