1) Amperometric biosensor
电流式生物传感器
2) current
电流
1.
Experiments on Effects of M-EMS Current on Quality of Bloom;
结晶器电磁搅拌电流对大方坯质量影响试验
2.
Simulating effects of electric current and molar of C to N on denitrification rates in biofilm of bio-electro reactor;
电流和碳氮的量比对生物电极脱氮速率影响的模拟
3.
Study on the Influence of Self-Consumable Electrode's End Shape by the Current in the Electroslag Casting Process;
电渣熔铸中电流对自耗电极端部锥角影响的研究
3) electric current
电流
1.
Heat sink project of big electric current in the low-temperature measurement;
低温大电流测量中热沉的设计
2.
To measure the electric parameters with the electrical machinery adopted on the progressive cavity pump well,the electric current,electric tension,power factor and so on,and calculate the torque rating output from the electrical machinery,then calculation of the torque rating of the polish rod is done.
通过测量得到地面驱动螺杆泵电机的工作电流、电压和功率因数等电参数,采用考虑电机内部损耗的计算方法,得到电机的输出轴扭矩,经换算得到光杆扭矩。
3.
In this paper,the changes of the passivation layer's state,indicated by the electric current,have been analyzed in every phase of ELID grinding.
建立了ELID磨削系统的电解反应回路等效模型,提出用极间电流表征金属结合剂砂轮表面的钝化膜状态,分析了钝化膜在ELID超精密镜面磨削电解预修锐阶段、在线电解修整动态磨削阶段和光磨阶段的状态变化。
4) electrical current
电流
1.
Parameters of Electrical Current and Speed Used in Thermal Error Prediction of Machining Center;
基于电流与速度参数的加工中心热误差预测方法
2.
Applying impeller cutting method to reduce circulation pump running electrical current;
叶轮切削法在降低热网循环泵运行电流中的应用
3.
Experimental study on the friction and wear behavior of 1Cr18Ni9Ti/copper-impregnated metallized carbon was carried out under the conditions of different loads,sliding speed and electrical current on a pin-on-disc tester.
在销-盘摩擦磨损试验机上试验了载荷、速度、电流对1Cr18Ni9Ti/浸金属碳对磨时的摩擦因数、磨损量及磨损形貌的影响。
5) A-currents
A-电流
6) current strength
电流
参考词条
补充资料：变压器式传感器
利用变压器作用原理把被测位移转换为初、次级线圈互感变化的变磁阻式传感器。它由两个或多个带铁心的线圈构成，初、次级线圈间的互感能随衔铁或两个线圈间的相对移动而改变。当用适当频率的电压激励初级线圈时,次级线圈的输出电压将随互感的改变而变化,从而将被测位移转换为电压输出。这种传感器在使用中常采取两个同名端串接的次级绕组线圈，以差动方式输出，所以又称为差动变压器式传感器。变压器式传感器的特点与电感式传感器相同，有时亦称电感式传感器。但变压器式传感器在设计上具有更大的灵活性，应用更为广泛。旋转变压器、感应同步器、自整角机都属于变压器式传感器。变压器式传感器主要用于测量位移和能转换成位移量的力、张力、压力、压差、加速度、应变、流量、厚度、比重、转矩等参量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。