1) iron carbide
铁碳化物
1.
The results show that the formation of iron carbide is related to the interaction between the active component and the support of the catalysts.
结果表明:铁碳化物的生成与催化剂活性组分同载体的相互作用有关。
2) Iron-carbon
铁碳
1.
The article preliminaryly discusses the influence factor of organic pollutant which difficultly degrades in Iron-carbon degradative water,the best technological parameter and treated effect;It also inquires into effect mechanism of oxidizing degradative polltant,through analyzes midium result of pollutant degradation and puts foward possible way of pollutant degradation.
铁碳降解水中难降解有机污染物的影响因素、最佳工艺参数及处理效果;初步探讨了氧化降解污染物的作用机理;通过分析污染物降解的中间产物,提出了污染物降解的可能途径。
3) Fe/C
铁/碳
1.
A process for preparation of the potassium methylate with the potassium-mercury amalgam and methanol using Fe/C as catalyst was provided.
本文主要研究了甲醇与钾汞齐在铁/碳催化剂作用下合成甲醇钾的工艺。
4) Fe-C method
铁碳法
1.
Biochemical method and Fe-C method were used for the treatment of terephthalic acid wastewater.
采用生化法和铁碳法进行对苯二甲酸废水的处理研究,结果得出:CODCr=2000mg/L是微生物降解对苯二甲酸的抑制质量-体积分数;pH值为8~9时活性污泥处理对苯二甲酸废水比较理想;铁碳法处理对苯二甲酸废水35h后,CODCr的去除率达到了80%以上。
2.
The Fe-C method,which is used to treat the CR wastewater containing high level PSA,is a pretreatment technology on the worksite.
介绍以铁碳法处理冷轧含高浓度PSA废水的处理技术,结合现场设计铁碳技术为主要的预处理工艺,大幅度降低COD浓度,去除Sn~(2+)离子,为废水进一步进行生化处理提供保障。
5) Fe/C
铁碳比
1.
The results indicated that the optimized condition of ferric-carbon microelectrolysis is pH=2, Fe/C=1∶2, HRT=2 h.
实验结果表明,最合适反应条件是进水pH值为2、铁碳比1∶2、停留时间为2h,在此条件下CODCr去除率可达64%以上,且进水浓度的变化对去除率影响不大。
6) iron-carbon system
铁碳体系
1.
Investigation of mechanism of wastewater decontamination with reaction of hydrogen separation and oxygen absoption in iron-carbon system;
铁碳体系析氢与吸氧反应过程净化废水机理的研究
参考词条
铁-碳化钛
铁碳钛齐
铁碳相图
聚铁碳硅烷
铁碳内电解
铁碳微电解
铁-碳原电池
二茂铁碳酰
铁碳析出物
铁碳化合物
铁碳镍铁<冶>
铁碳微电解工艺
铁碳合金相图
铁碳曝气氧化
超光滑光学表面
内存防护
补充资料:碳化硅晶须补强碳化硅陶瓷基复合材料
分子式:
CAS号:
性质:以碳化硅陶瓷为基和以碳化硅晶须为增强剂的新型陶瓷材料。通过晶须的载荷转移、拔出及裂纹偏转作用,获得比普通碳化硅更高的强度和韧性。使用温度达1400℃。是一种重要的高温结构陶瓷。用于燃气轮机叶片等高温部件和耐磨件制造。采用原位生长工艺和烧结工艺制取。
CAS号:
性质:以碳化硅陶瓷为基和以碳化硅晶须为增强剂的新型陶瓷材料。通过晶须的载荷转移、拔出及裂纹偏转作用,获得比普通碳化硅更高的强度和韧性。使用温度达1400℃。是一种重要的高温结构陶瓷。用于燃气轮机叶片等高温部件和耐磨件制造。采用原位生长工艺和烧结工艺制取。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。