1) multiphase ceramics composites
多元系复相陶瓷
1.
The preparation technology of ZrO2 toughened A12O3-TiC multiphase ceramics composites and the effect of ZrO2 content on the properties of fracture toughness, bending strength, Vicker hardness of composites have been investigated in the paper.
本文通过对ZrO_3增韧Al_2O_3—TiC系复相陶瓷材料的制备工艺以及ZrO_2含量的变化对材料断裂韧性、抗弯强度以及硬度的影响研究,采用X射线衍射法分析断口相变量随组成变化对多元系复相陶瓷断裂韧性、抗弯强度的影响,同时分析在不同冲击工况下其耐冲蚀磨损特性与力学性能之间的关系。
2) multiphase composite ceramics
多相复合陶瓷
1.
The forming process of low cost and reliability is the key to make the multiphase composite ceramics industrialized.
低成本、高可靠性成型工艺是多相复合陶瓷产业化的关键。
3) composite ceramics
复相陶瓷
1.
Preparation of cordierite-mullite composite ceramics;
堇青石-莫来石复相陶瓷制备
2.
Sintering behavior and dielectric property of BST-BZN composite ceramics
BST-BZN复相陶瓷的烧结行为和介电性能
3.
Study on the dielectric properties of MgO-Ba(Zr_(0.2)Ti_(0.8))O_3 composite ceramics
MgO-Ba(Zr_(0.2)Ti_(0.8))O_3复相陶瓷介电性能研究
4) composite ceramic
复相陶瓷
1.
Effect of BN content on the properties and microstructure of AlN-BN composite ceramics by injection molding;
BN含量对注射成形AlN-BN复相陶瓷性能和组织的影响
2.
Preparation of Al_2O_3-based composite ceramics by combining hydrothermal processing with co-precipitation;
Al_2O_3基复相陶瓷共沉淀—水热法制备研究
3.
3SrO·(1-y)TiO2·yNb2O5)composite ceramics were prepared by sol-gel method in which BST slabby sol solution were fabricated firstly to suspend Nb2O5 fine powders.
yNb2O5)复相陶瓷。
5) multiphase ceramic
复相陶瓷
1.
Preparation and characteristics research of the doping W~(6+) into Zr(WV)_xO_y multiphase ceramic
掺杂W~(6+)的Zr(WV)_xO_y质复相陶瓷的制备及特性研究
2.
Nano multiphase ceramic helix muzzle was made of nano-ZrO2 and micron Al2O3, experiment results proved that nano-ZrO2 help to preparation thin crystal ZTA multiphase ceramic.
以纳米ZrO2、微米Al2O3为原料制备纳米复相陶瓷喷嘴。
3.
Friction and wear behaviors were studied for Ti_3SiC_2/SiC multiphase ceramics/45 steel pairs under unlubricated and lubricated.
研究了由热等静压原位合成的Ti3SiC2/SiC复相陶瓷与45#钢在干摩擦和边界油润滑条件下的摩擦磨损特性。
6) ceramic composite
复相陶瓷
1.
Crack extension behavior of intragranular ceramic composites;
内晶结构复相陶瓷的裂纹扩展行为
2.
ZrO_2/SiC-WSi_2/MoSi_2 ceramic composites were prepared by hot-pressed sintering after ZrO_2 and SiC nanoparticles were dispersed and mixed by wet-milling.
将纳米 ZrO_2和 SiC 颗粒与微米 WSi_2/MoSi_2颗粒进行球磨分散、混合,通过热压烧结制备 ZrO_2/SiC-WSi_2/MoSi_2复相陶瓷,研究了它的显微结构与耐磨性并与 MoSi_2材料进行了对比。
补充资料：多元醇系环氧树脂
分子式：
CAS号：
性质：由多元醇和环氧氯丙烷合成的一类环氧树脂，一般要比双酚A型环氧树脂黏度低，而且能溶于醇类和水中，固化后的产物有很好的柔韧性。比如中国牌号为B-63的树脂是甘油与环氧氯丙烷制成的树脂，其环氧指数为5.5～7.1，黏度约300mPa·s；日本东都公司YH-300树脂是由三羟甲基丙烷与环氧氯丙烷制得的，环氧含量140～155，黏度(25℃)为140～200mPa·s。可用作涂料和活性稀释剂。
CAS号：
性质：由多元醇和环氧氯丙烷合成的一类环氧树脂，一般要比双酚A型环氧树脂黏度低，而且能溶于醇类和水中，固化后的产物有很好的柔韧性。比如中国牌号为B-63的树脂是甘油与环氧氯丙烷制成的树脂，其环氧指数为5.5～7.1，黏度约300mPa·s；日本东都公司YH-300树脂是由三羟甲基丙烷与环氧氯丙烷制得的，环氧含量140～155，黏度(25℃)为140～200mPa·s。可用作涂料和活性稀释剂。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条