1) vessel plate
容器板
1.
Current situation of steel plate's quality for boiler and pressure vessel at present in China and technical reformation of equipment and so on are introduced, many kind of quality problems existed in enterprise for producing boiler and pressure vessel plates are particularly pointed out.
介绍了目前我国锅炉和压力容器用钢板的质量现状、设备技术改造等情况，以及在锅炉板和压力容器板生产中存在的一些问题。
2) plate; condenser armature; condenser coating
电容器板
3) vessel
容器
1.
Strain Test and Analysis of Fiberglass Winding Pressure Vessels;
玻璃纤维缠绕容器的水压应变测试及分析
2.
Numerical simulation of flammable gas explosions in closed vessel built-in obstacle;
设置障碍物密闭容器内气体爆炸数值模拟
3.
The quick calibration of liquid level in the vessel;
容器液位标尺的快速标定
4) container
容器
1.
The functional relationship between the height and the volume of the remaining liquid in the containers with changeful cross section;
变形截面容器内液体体积与液位高度关系
2.
The functional relationship between height and volume of the remaining liquid in the petrochemical containers;
容器内存留液体体积与液位高度函数关系
3.
Research state of liquid movement and control function in containers;
容器中液体运动及控制作用的研究现状
5) vessels
容器
1.
Weir Plate Thickness Calculation for Horizontal Vessels;
卧式容器中挡板厚度的计算
2.
According to service condition and theory of correlation,this paper analyzes the influence of temperature on the vessels design in choosing of the vessels material,determining of admissible stress and design methods.
通过对实际使用情况和相关理论的分析,着重从温度对容器材料的选用、许用应力选取,容器设计方法的影响进行了研究。
3.
This is a reference calculation of unfolding shapes of pressure vessels for the technicians deal with the pressure vessels design and manufactur
主要介绍压力容器管材、板材的下料尺寸及展开尺寸的计算 ,以供压力容器设计、制造工程技术人员参考使用。
6) tank
容器
1.
When LPG tanks are exposed to fire, the internal pressure of tanks will increase quickly and the strengh will decline,so the tanks may explode in a short period.
液化气体容器在火灾环境下由于内部压力升高和容器本身强度的下降,爆炸的危险性极大。
2.
To probe into the stress distribution of tanks composed of cone sheels,the steel tank model is tested The stress distribution of the tank is analyzed through equilibrium theory of thin shell Then the formulae for design of stress and the stability analysis conclusion of the tank are give
为探讨锥壳组合容器的应力分布 ,通过钢制容器模型的试验 ,并根据薄壳平衡理论分析容器的应力分布 ,得出适合于工程应用的应力计算公式和稳定验算结
参考词条
补充资料：凹板印刷机用胶布板
分子式：
分子量：
CAS号：
性质：用于高速轮转凹版印刷机的胶布板。供印刷报纸、杂志、图书等。与凸版印刷机用胶布板的装置位置相同，不与油墨直接接触，但作用不同，通过橡皮表层的弹力作用，将凹沟内的油墨吸到纸张上。印刷时所受的压力较大，胶层须较厚。
分子量：
CAS号：
性质：用于高速轮转凹版印刷机的胶布板。供印刷报纸、杂志、图书等。与凸版印刷机用胶布板的装置位置相同，不与油墨直接接触，但作用不同，通过橡皮表层的弹力作用，将凹沟内的油墨吸到纸张上。印刷时所受的压力较大，胶层须较厚。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。