1) non saturable polyester resin
不饱和聚酯数脂
2) unsaturated polyester resin
不饱和聚酯树脂
1.
Studies on flexible unsaturated polyester resin from polyether glycol and its flexible curing system;
聚醚二元醇不饱和聚酯树脂及其柔性固化体系
2.
Modified unsaturated polyester resin by N-phenyl maleimide;
N-苯马来酰亚胺改性不饱和聚酯树脂
3.
Advances in modification of unsaturated polyester resin;
不饱和聚酯树脂改性研究进展
3) unsaturated polyester
不饱和聚酯树脂
1.
Stabilization process advance of unsaturated polyester resin;
不饱和聚酯树脂的稳定化技术进展
2.
The preparation and stability of unsaturated polyester W/O emulsions;
不饱和聚酯树脂 W/ O型乳液的制备及其稳定性
3.
The various influencing factors and main synthesis processes of dicy clopentadiene modified unsaturated polyester resin are investigated.
探讨了双环戊二烯改性不饱和聚酯树脂的各种影响因素及其合成的主要工艺条件。
4) UPR
不饱和聚酯树脂
1.
The effect of SiO_2 addition on the mechanical properties of UPR;
二氧化硅对不饱和聚酯树脂浇铸体力学性能的影响
2.
The development and application of unstaturated polyester resion (UPR) are summarized.
综述了近年来不饱和聚酯树脂的发展及应用。
3.
Benzoperoxide/N,N-dimethylaniline initiator system that can eliminate the danger of using MEKPO/Co salt system used in UPR at room temperature was studied in this paper.
采用过氧化苯甲酰/N,N-二甲基苯胺(DMA)固化体系室温条件下对不饱和聚酯树脂(UPR)进行固化,可以降低常用的过氧化酮/钴盐体系的危险性。
5) UP resin
不饱和聚酯树脂
1.
This paper studies the self-made low profile additive and its influence on shrinkage rate and mechanical properties of UP resin.
本文研究了自制低收缩添加剂用量对不饱和聚酯树脂固化收缩率与力学性能的影响。
2.
The paper investigates the influence of structure, mould design, moulding process, regulating and coating on the warpage of UP resin DMC moulded panel, related control measures are also provided.
探讨了结构、模具设计、模压工艺条件、整形处理及涂漆等因素对不饱和聚酯树脂DMC模塑面板翘曲变形的影响,并提出相应的控制措施。
3.
The casting and FRP flame retardancy rule of UP resin are studled and a resin system for panel which is of good flame retardancy property,mechanical property satisfied for design,effectiye process,and low cost etc.
本文以不饱和聚酯树脂为研究对象，探讨其浇铸体和玻璃钢的阻燃规律，寻求阻燃性能优异、力学性能满足要求、工艺可行、成本低的面板用树脂体系。
补充资料：聚酯
| 聚酯 polyesters 主链上含重复酯基结构的聚合物。由多元酸和多元醇经缩聚而成。二元酸与二元醇缩聚得到线性聚酯，最重要的是聚对苯二甲酸乙二酯（见涤纶）。官能度大于 2 的酸和醇缩合得到体型聚酯，如醇酸树脂。不饱和二元酸和二元醇缩聚得到不饱和聚酯。此外尚存下列工业上较重要的线性聚酯。①聚对苯二甲酸二丁酯。由对苯二甲酸与1 ，4 -丁二醇在钛催化下经酯交换再缩聚而成。熔融温度220～225℃ ，玻璃化温度36～49℃。可作工程塑料，也可熔纺成纤维。如果两端含羟基，可用来制备多嵌段聚醚聚酯热塑弹性体。②聚对苯二甲酸-1 ，4-环己烷二亚甲基酯 。由对苯二甲酸二甲酯与1 ，4-二羟基甲基环己烷经酯交换后再缩聚而得。结晶度为50％时，熔点为290～295℃ ，非晶态聚合物的玻璃化温度为85℃。纺得的纤维膨松，可制作地毯或用作填充料。 |
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条