1) The constitutional stand of bush
组织轴承座
2) Bearing housings assembly
轴承座组装
3) bearing seat
轴承座
1.
Analysis of two types of central bearing seats of pumping units;
抽油机中央轴承座2种形式的分析
2.
Based on the process improvement of bearing seat and numerical forming simulation,the rational project and the best process parameters were established.
通过对轴承座零件的工艺改进和成形数值模拟,最终确定了合理工艺方案和最佳成形参数,并在生产实践中得以验证,达到了节约成本,提高生产率的目的。
3.
By means of spectrum analysis technology,the article inspects and diagnoses centrifugal compressor unit,analyzes the vibration features of compressor shell,rotor and bearing seat,finds out abnormal vibration and logical connection among vibration features in three position,according to the rotor unbalance conclusion,main- rains the unit,recovers normal operation of the unit.
利用频谱分析技术,对离心式压缩机机组进行状态监测和诊断,分析压缩机机壳、转子、轴承座的振动特征,查找振动异常的原因及三个部位振动特征间的逻辑联系,根据转子不平衡结论,对机组进行维修,恢复了机组的正常运行。
4) Bearing Chock
轴承座
1.
The detail forced status of the shaft of the overturn frame in the bearing chock overturn device has been described in this article,meanwhile the calculation review has been performed to the shaft rigidity after the structure upgrading finished.
针对某轴承座翻转装置中翻转架转轴的具体受力状况进行分析,并对改进结构后的转轴刚度进行计算校核。
2.
In this paper,the authors analyzed by energy stable method that the stability of bearing chock of work roll about 2200mm high speed aluminum foil mill under two different restrict conditions which the gaps between bearing chock and bousing window are given or not.
用能量稳定法对 2 2 0 0mm高速铝箔轧机辊系中工作辊轴承座同机架窗口侧向有隙或无隙两种不同约束条件下的稳定性进行了分析。
3.
The heat distortion of workroll bearing chock of 2050mm hot strip rolling mill employed in Baoshan continuous rolling mill is studied using finite element method(FEM),3D FEM temperature distribution program and SAP5 software.
以宝钢 2 0 50热连轧机工作辊轴承座的热变形故障作为研究对象 ,详细分析了轴承系统的内热源 ,确认轴承内部的摩擦热是轴承系统温升的主要热源 ,本文采用有限元方法 ,同时利用三维有限元温度场程序和SAP5软件 ,研究了轴承座的热变形场分布规律。
5) bearing
[英]['bɛəriŋ，'beərɪŋ] [美]['bɛrɪŋ]
轴承座
1.
Hydraulic System Design of Disassembly and Assembly Device for Huge Roller Bearing;
大型轧辊轴承座拆装机液压系统设计
2.
The authors described in detail the development of the new bearing, which can enlarge the moment, using dynamics analyses of the structural principle.
全面介绍了强化型管口轴承座的研制工作,进行了初步结构原理的动力学分析,并且测试了数种不同结构参数的轴承座的工作力矩特性。
3.
The position and the appearance characters of the crack of bearing had been confirmed through testing experiment.
通过检验分析确定了轴承座裂纹的位置与形貌特征,分析了轴承座裂纹产生的原因,探讨了解决裂纹的措施。
6) bearing pedestal
轴承座
1.
The technological characteristic of the bearing pedestal was analyzed.
分析了轴承座的工艺特点,采用复合模加工,保证了零件精度,简化了加工工艺,并介绍了模具结构及其关键零部件的设计要点。
2.
1 in Zhanjiang Power Plant has been analysed,and it is believed that the main causes to be as follows:(1)large deformation of the lowpressure cylinder leading to collision and friction between moving and stationary parts;(2)the vacant space under bearing pedestal and turninggear box bringing on lower rigidity;(3) the natural frequency of bearing pedestal is closing to the power frequency etc.
对湛江发电厂1号机4号轴瓦振动大的问题进行分析,认为其主要原因为:低压缸变形大导致动静碰摩,轴承座及盘车箱下部脱空引起刚度降低,轴承座的固有频率与工频相近等。
3.
The axial vibration of bearing pedestal is referring to vibration in same direction of the rotor shaft s centre line.
在汽轮发电机组,特别是一些中、小容量机组的运行中,轴承座的轴向振动是其垂直或水平振动的数倍甚至几十倍。
补充资料：《国际民用航空组织和世界旅游组织工作协议》
《国际民用航空组织和世界旅游组织工作协议》
《国际民用航空组织和世界旅游组织工作协议》有关旅游的国际协议之一。由国际民用航空组织秘书长和世界旅游组织秘书长经协商制定。此协议一共7条。根据此协议，双方秘书处本着互利的原则交流民用航空和旅游方面的信息和资料;双方可以派代表以观察员的身分参加对方的会议;在公开会议上，观察员有权获得会议文件和发言;双方可以在人才、资料、设备等方面互相支持。世界旅游组织秘书长和国际民用航空组织理事会主席可以通过协商修改协议的条款。此协议自1978年9月1日起生效。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条