说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 轴承座孔
1)  bearing saddle bore
轴承座孔
1.
Taking the correction of the gear shaft and bearing saddle bore of a reducer as the example, this paper probes into the problem of the correction of the gear shaft and bearing saddle bore often encountered in the inspection of e lectromechanic equipment, and according to the practical experiences, makes emph atically discussion on the brush plating repair technique.
以某减速机齿轮轴与轴承座孔的修复为例,对机电设备检修工作中经常遇到的齿轮轴和轴承座孔修复问题进行了探讨,并根据实践经验对刷镀修复工艺要点进行了重点论述。
2)  pinion bearing cup counterbore
小齿轮轴承外环座孔
3)  rudder bearer bracket
舵承座孔
1.
Following the mentioned procedure of determination of the interference,rudder bush loosen and rudder bearer bracket corrosion will be considerably avoided.
修船中常会遇到铜质舵承出现松动,舵承座孔被腐蚀的情况。
4)  bearing seat
轴承座
1.
Analysis of two types of central bearing seats of pumping units;
抽油机中央轴承座2种形式的分析
2.
Based on the process improvement of bearing seat and numerical forming simulation,the rational project and the best process parameters were established.
通过对轴承座零件的工艺改进和成形数值模拟,最终确定了合理工艺方案和最佳成形参数,并在生产实践中得以验证,达到了节约成本,提高生产率的目的。
3.
By means of spectrum analysis technology,the article inspects and diagnoses centrifugal compressor unit,analyzes the vibration features of compressor shell,rotor and bearing seat,finds out abnormal vibration and logical connection among vibration features in three position,according to the rotor unbalance conclusion,main- rains the unit,recovers normal operation of the unit.
利用频谱分析技术,对离心式压缩机机组进行状态监测和诊断,分析压缩机机壳、转子、轴承座的振动特征,查找振动异常的原因及三个部位振动特征间的逻辑联系,根据转子不平衡结论,对机组进行维修,恢复了机组的正常运行。
5)  Bearing Chock
轴承座
1.
The detail forced status of the shaft of the overturn frame in the bearing chock overturn device has been described in this article,meanwhile the calculation review has been performed to the shaft rigidity after the structure upgrading finished.
针对某轴承座翻转装置中翻转架转轴的具体受力状况进行分析,并对改进结构后的转轴刚度进行计算校核。
2.
In this paper,the authors analyzed by energy stable method that the stability of bearing chock of work roll about 2200mm high speed aluminum foil mill under two different restrict conditions which the gaps between bearing chock and bousing window are given or not.
用能量稳定法对 2 2 0 0mm高速铝箔轧机辊系中工作辊轴承座同机架窗口侧向有隙或无隙两种不同约束条件下的稳定性进行了分析。
3.
The heat distortion of workroll bearing chock of 2050mm hot strip rolling mill employed in Baoshan continuous rolling mill is studied using finite element method(FEM),3D FEM temperature distribution program and SAP5 software.
以宝钢 2 0 50热连轧机工作辊轴承座的热变形故障作为研究对象 ,详细分析了轴承系统的内热源 ,确认轴承内部的摩擦热是轴承系统温升的主要热源 ,本文采用有限元方法 ,同时利用三维有限元温度场程序和SAP5软件 ,研究了轴承座的热变形场分布规律。
6)  bearing [英]['bɛəriŋ,'beərɪŋ]  [美]['bɛrɪŋ]
轴承座
1.
Hydraulic System Design of Disassembly and Assembly Device for Huge Roller Bearing;
大型轧辊轴承座拆装机液压系统设计
2.
The authors described in detail the development of the new bearing, which can enlarge the moment, using dynamics analyses of the structural principle.
全面介绍了强化型管口轴承座的研制工作,进行了初步结构原理的动力学分析,并且测试了数种不同结构参数的轴承座的工作力矩特性。
3.
The position and the appearance characters of the crack of bearing had been confirmed through testing experiment.
通过检验分析确定了轴承座裂纹的位置与形貌特征,分析了轴承座裂纹产生的原因,探讨了解决裂纹的措施。
补充资料:第二孔(继发孔)型缺损


第二孔(继发孔)型缺损
ostium secondary defect

是心房间隔在形成上发生障碍,一般缺损较大,多在卵圆孔附近称第二孔(继发孔)型缺损。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条