1)  creep deformation
蠕变形变
2)  creep
蠕变
1.
Analysis on Stress and Strain Behavior of Spherical Vessel of Functionally Graded Material under Creep Condition;
蠕变条件下梯度材料球罐应力应变行为分析
2.
Study on Creep Behavior of PPS/SiO_2 Composites;
PPS/SiO_2复合材料蠕变行为的研究
3.
Acoustic Emission Characteristic of C/SiC Composite During Creep at High Temperature;
C/SiC复合材料高温蠕变的声发射特性
3)  creep deformation
蠕变
1.
Application of grey theory in forecasting creep deformation of geotechnic grate;
灰色理论在土工格栅蠕变预测中的应用
2.
Key factors for micro-displacement resolution of piezoelectric actuators are systematically summarized in following two aspects: intrinsic(hysteresis;creep deformation) and extrinsic(environment;control power;pretightening force;guide mechanism etc.
从内在因素(迟滞和蠕变效应)和外在因素(环境、控制电源、预紧力、导向机构等)两大方面系统的总结了压电驱动微位移灵敏度的影响因素,并针对每种因素给出了相应的实验结果或调研数据,提出了提高分辨率可采取的措施。
3.
Based on the experienced knowledge of the course of slope creep deformation.
基于对边坡蠕变过程的先验认识,借鉴澳大利亚联邦科学和工业组织数学统计部DvidA。
4)  creep behavior
蠕变
1.
Analysis of creep behavior of resin-based 3-D braided composites;
树脂基三维编织复合材料蠕变性能分析
2.
Based on the creep behavior with thermal viscoplasticity analysis,a computational procedure was presented for analyzing temperature fields and residual stress states in multi-pass welds and post-weld heat treatment in steel pipes with similar and dissimilar welded joint.
采用热-粘弹塑性有限元模型,在考虑蠕变效应的基础上,对同种及异种钢管子环焊缝焊接及焊后热处理过程进行了数值模拟。
3.
Methods The creep behaviors of the cryopreserved arteries were observed with different cryopreservation methods by using a dynamic mechanical analyzer(DMA-2980,TA Instruments,New Castle,Delaware,USA).
方法使用动态力学分析仪(DMA-2980,TA In-struments,New Castle,Delaware,USA)比较研究不同低温保存方案下动脉蠕变行为与新鲜对照组的差异。
5)  creepage
蠕变
1.
Analysis on Deflection and Creepage of OSB;
定向刨花板挠度与蠕变试验
2.
, upon bolt s creepage and fatigue damage has been analysed.
提出了一种评估高温紧固螺栓剩余寿命的计算模型 ,并对一实际螺栓进行了具体计算 ,在此基础上分析了装配、运行及材料性能等因素对螺栓蠕变和疲劳损伤的影响。
6)  creeping
蠕变
1.
Automatic test technique of overhead electrical conductors creeping;
架空导线蠕变的自动测试技术
2.
If the support time is very late,for the adjacent rock a large displacement would arise because of the influence of creeping.
若支护时间过早,衬砌因围岩蠕变的影响将产生较大的变形和所承受的荷载较大,从而出现破坏现象;若支护时间过晚,围岩因蠕变的影响产生较大的位移而失稳,从而引发跨塌等工程事故。
3.
Keeping track of creeping based on the characters of the creeping course and zeroing changing, the exact load was confirmed.
分析电阻应变式传感器蠕变特性,利用其加/卸载和蠕变输出变化率的不同,判断蠕变起始点,根据蠕变过程和零点变化的特点进行蠕变跟踪,以此确定传感器实际载荷。
参考词条
补充资料:CJ-2计算机控制陶瓷材料高温蠕变试验机


CJ-2计算机控制陶瓷材料高温蠕变试验机


  鲡 C」一2计算机控制陶瓷材料高温蠕变试验机 中国科学院上海硅酸生研完所供稿
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。