说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 蠕变模型
1)  creep model
蠕变模型
1.
Non-linear creep model of rock and parameter determination;
岩石试件非线性蠕变模型及其参数确定
2.
Study on nonlinear creep model for saturated sand;
饱和砂性土非线性蠕变模型试验研究
3.
Experimental study of creep model and failure characteristics of coal
煤岩蠕变模型与破坏特征试验研究
2)  Mesri creep model
Mesri蠕变模型
1.
By Mesri creep model, using the Mindlin stress formula to calculate the stress induced by the load of pile; and using Boussinesq stress formula to calculate the stress induced by the load of raft; a simple but practical method for predicting l.
采用Mesri蠕变模型描述土体的蠕变行为,用桩的Mindlin应力公式计算桩端和桩侧荷载在桩端平面以下产生的附加应力,用Boussinesq应力公式计算承台分担荷载产生的应力。
2.
Based on those tests a shear stress-strain-time function, Mesri creep model, in which a hyperbola is adopted for shear stress-strain behaviour and power.
并在此基础上,给出了排水条件下粘性土的Mesri蠕变模型,即剪应力-应变关系采用双曲线模型,应变-时间关系采用幂函数来描述土体的弹粘塑性。
3)  Heard creep model
Heard蠕变模型
1.
Regression analysis on the test data was done by use of creep material mode-Heard creep model.
利用蠕变材料本构模型—Heard蠕变模型进行了试验数据回归分析,并对模型的适用条件进行了论证。
4)  power law creep model
幂律型蠕变模型
5)  exponential creep model
指数蠕变模型
1.
In order to determine the secondary support time and intensity,the changing rules of the stress and deformation speed of surrounding rocks with time,the effects of the secondary supporting time and intensity of surrounding rocks on deformation were analyzed using exponential creep model of FLAC2D at west tunnel in the Guhanshan Mine of Jiaozuo Coal Industry Group.
为了研究确定高应力软岩巷道二次支护时间和支护强度,以焦煤集团古汉山矿西大巷为研究对象,采用FLAC2D中的指数蠕变模型,研究分析围岩应力和围岩变形速度随时间的变化规律、二次支护时间及支护强度对围岩变形的影响规律。
6)  creep damage model
蠕变损伤模型
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条