1) electrode E4316
E4316焊条
2) welding rod
焊条
1.
Improvement method of testing welding rod surface parting shape dimensions using lock phase amplifier;
锁相放大器测试焊条表面分形维数的改进
2.
The influence of melt slag basicity to welding rod coating alloying element transition coefficient;
熔渣碱度对焊条药皮中合金元素过渡系数的影响
3) covered electrode
焊条
1.
Evaluation of typical metal transfer modes for covered electrode;
焊条典型熔滴过渡形态的判读
2.
and the tendency for hydrogen - induced cracking of the T91/ 12Cr1MoV joint welded with different covered electrodes was investigated by means of electrolytic hydrogen charging and constant - load delayed cracking test.
用甘油法测定了从日本进口的ＣＭ－９Ｃｂ焊条、国内新研制的Ｔ９１专用焊条以及Ｒ３１７焊条熔敷金属中的扩散氢含量。
4) Electrode
[英][ɪ'lektrəʊd] [美][ɪ'lɛktrod]
焊条
1.
Application of Complex Ferroalloy in Coating of Electrodes;
复合铁合金在焊条药皮中的应用
2.
Special electrode with high temperature corrosive resistance;
抗高温氧化腐蚀专用焊条
3.
The study of electrode for line pan of scraper conveyer;
刮板输送机中部槽耐磨焊条研究
5) welding electrode
焊条
1.
According to a new type of frog made of granular bainitic steel,the paper researches a special welding electrode for repairing and joining.
针对新型辙叉用贝氏体钢,研制出一种焊接工艺性能良好、焊缝组织为粒状贝氏体的、用于焊接修补和连接的专用焊条。
2.
CHE607GX is a kind of welding electrode with high toughness and low sulphur fox X70 pipeline steel in China .
研制了X70管线钢配套用低硫高韧性焊条。
6) manual electrodes
焊条
1.
On the basis of study on the weldability of 40Cr steel and 55Si2Mn steel,welding process test was contrasted among different manual electrodes and different combined of manual electrodes.
在对40Cr/55Si2Mn钢焊接性分析的基础上,进行了多种焊条和焊条组合的焊接工艺对比试验,并对焊缝和接头进行了相应的性能测试和显微组织观察。
2.
According to requirements of large size gear of mine and cement machinery for surfacing wear resistant performance,research was concentrated on surfacing manual electrodes possessingimpact resistance and mid-metals contact fatigue wear resistance.
根据矿山机械、水泥机械等大型齿轮磨损堆焊性能的要求，有针对性的研制出了具有耐冲击、金属间接触疲劳磨损的堆焊焊条。
补充资料：低温钢焊条
低温钢焊条
covered electrode for low temperature steel
d一wengang hantlao低温钢焊条(eovered eleetrode for low tem-perature steel)专用于焊接低温钢的焊条。根据使用温度的不同，低温用钢可分为一40℃、一60℃、一70℃、一90℃、一100oC、一196℃和一253℃几个级别，低温钢焊条的分级与钢种的分级相一致，并要求焊缝韧性与同级别的钢种相匹配。为了提高焊缝韧性，低温钢焊条均采用碱性低氢型药皮，并对焊缝成分有较严格的要求:一40℃用的焊条，其焊缝成分可含1.5肠Ni，也可不含镍而含微量的钦和硼;一60‘C用焊条，其焊缝成分可含2.5%Ni，也可含1%Ni和微量的钦、硼;一90一一100℃用焊条，其焊缝中含镍量可达3%~5%;一196℃以下用的焊条，往往采用奥氏体组织的焊条。 采用低温钢焊条施焊时，应尽量采用较小的焊接线能量，预热和层间温度也宜控制得低一些，以便改善焊缝区和热影响区的韧性。但是，随着焊缝中合金含量的增多，裂纹敏感性增高，为防止焊接裂纹应采取适当预热，层间温度应不低于预热温度，但不要超过200一300‘C。 (尹士科)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条