1) LoSolid cooking
低固形物
2) Lo-solids cooking
低固形物蒸煮
1.
The development of Lo-solids cooking process was very fast.
低固形物蒸煮技术(Lo-solids cooking)发展很快,很多原来采用MCC和EMCC蒸煮方法的纸厂,现在改用Lo-solids蒸煮技术。
3) Lo-Solids cooking process
低固形物蒸煮工艺
1.
It was changing the upflow Lo-Solids cooking process to downflow Lo-Solids cooking process.
通过对一例升流低固形物蒸煮器内木片架桥事故的描述及原因分析,提出在机械、仪表、工艺操作控制方面对连蒸器内木片架桥故障的预防处理措施,重点介绍升流式低固形物蒸煮工艺系统超设计能力运行时,出现木片料柱运动障碍可能引起木片架桥时的有效解决方法,即蒸煮工艺由升流低固形物蒸煮改造转换为"降流"低固形物蒸煮。
4) solid content
固形物
1.
Effect of different solid content on the stability of the lactobacillus drink was studied in this paper.
系统研究了不同固形物对乳酸菌饮料稳定性的影响,通过对产品稳定性的分析测试及长时间观察,结果表明:蔗糖、CR3010添加量分别为10%～12%和1。
2.
The results showed that in the same categ ory on its10-days g rowth,the flavonoid and solid content level was hig her than at any other stag e and attained the maximum.
结果表明,同种麦叶中,10d生长期时黄酮类化合物及固形物含量明显高于其他时期,达到峰值。
5) solid
[英]['sɔlɪd] [美]['sɑlɪd]
固形物
1.
Effect of adding ways and content of some solids on the stability of the lactobacillus drink;
固形物添加方式及含量对乳酸菌饮料稳定性的影响
2.
The Difference between the Refractive Method and Dry Method for Measuring the Solid Substance of Starch Syrup;
折光法与干燥法测淀粉糖浆固形物的比较研究
3.
Study on reason and measurement of solids over standard in liquor;
浓香型白酒固形物超标原因及解决方法的研究
6) total solids
总固形物
1.
For the fermentation coupled with distillage recycle,every five days,the total backset distillage collected was directly used to mix the corn powder,and the experimental results revealed that the concentrations of ethanol,residual reductive sugar,inorganic phosphate and total solids in the broth were maintained s.
136 g/L和85 g/L左右;乙醇浓度与对照组相差不大,但残还原糖、无机磷及总固形物在废糟液循环使用的初期出现积累,但随运行时间的延长而趋于稳定,说明对酵母生长和乙醇发酵没有产生明显影响。
2.
The effects of chemical oxygen demand(COD),total solids,coloring;matter, ash contens, organic compound from black liquor have been studied.
探讨了黑液的化学耗氧量（CODmn）、总固形物、色度、灰分、有机物等指标之间的相互影响。
补充资料：线型低密度聚乙烯/低密度聚乙烯共混物
分子式：
CAS号：
性质：系由线性低密度聚乙烯与低密度聚乙烯组成的共混物，20％的低密度聚乙烯可显著改善线性低密度的加工性能，提高薄膜韧性和透光性，当低密度聚乙烯达50％时，可提高薄膜撕裂强度和断裂伸长率。可通过粒料直接掺混制备。主要用于吹塑农膜、包装膜及挤出包覆电缆。
CAS号：
性质：系由线性低密度聚乙烯与低密度聚乙烯组成的共混物，20％的低密度聚乙烯可显著改善线性低密度的加工性能，提高薄膜韧性和透光性，当低密度聚乙烯达50％时，可提高薄膜撕裂强度和断裂伸长率。可通过粒料直接掺混制备。主要用于吹塑农膜、包装膜及挤出包覆电缆。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条