1) high speed mixing
快速混捏
1.
Making use of the visible-conceal characters of mixing curve balance point and the d P d t value of the power spectrum curve, it is possible to analyze the paste situation and to determine the mixing time, and this leads to a high speed mixing procedure.
利用混捏曲线平衡点的显隐特点和功率谱曲线的 dPdt 值 ,分析糊料状态 ,确定混捏时间 ,从而实现快速混捏工艺。
2) Knead
[英][ni:d] [美][nid]
混捏
1.
Kneading Process Analyzing of the Past For Baking Anode;
预焙阳极糊料混捏工艺分析
3) rapid mixing
快速混合
1.
A new technique of gasgas ejecting rapid mixing was proposed, in which the flow characteristics caused by impingement and swirling between two streams promote gasgas rapid mixing.
介绍了一种气气喷射流快速混合技术,利用射流的碰撞及卷吸所产生的流动特性促进2股气体的快速混合。
2.
The results showed that turbine ejecting mixer was a rapid mixing apparatus with good mixing process of little mixing space,good mixing uniformity and high volume ratio of medium and anticratering spray nozzle.
研究结果表明,涡轮喷射混合器是能够满足混合均匀度要求高、介质体积比高和喷嘴能有效防堵的快速混合装置。
3.
The micromixing is the main cause of rapid mixing.
结果表明,混合均匀度随调节高度的增加而变大,最优设计参数条件下可达96%以上;该混合器抗冲击负荷能力强,流量增大31%时其混合均匀度仍可达92%;定制的特殊加药头可实现液膜状连续加药,有效提高混合效果;微观混合在快速混合中起主导作用。
4) Quick mixing
快速混配
5) fast mixing
快速混合
1.
Several industrial designs of liquidliquid fast mixing equipment and the study of their mixing mechanism are reviewed.
在分析了液液混合机理的基础上,对几类常用的液液快速混合设备及其混合过程机理方面的研究进行了全面的综述。
2.
The suitable parameters of mechanical agitation for water flocculation treatment are determined as follows:(1)Power input increases as the diameter of propeller is increased for fast mixing process.
75 m× 1 m方形搅拌槽中 ,利用配制的两种污水 ,以 Al2 ( SO4 ) 3· 1 8H2 O为絮凝剂 ,采用三种不同直径的轴流式 CBY型搅拌桨 ,分别得出适用于快速混合过程及絮凝过程的机械搅拌操作参数 :( 1 )对于快速混合过程 ,搅拌桨直径增加 ,絮凝剂混匀所需输入功率增大 ;( 2 )对于三级絮凝过程 ,三级絮凝搅拌桨叶端线速度之比为3∶ 2∶ 1 ,第一级叶端线速度的适宜范围为 :1 。
3.
As mixture for droplets is important and needs to be improved in lab-on-a-chip,a fast mixing method for digital droplets in micro-channel driven by surface acoustic wave is proposed.
微流体混合是微流控芯片急需完善的重要操作单元,提出了在声表面波驱动下实现微通道内数字微流体快速混合方法。
6) fast mixing chamber
快速混合器
补充资料:鬼捏青
1.无名青肿。旧时迷信以为鬼怪扭捏所致,故称。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条