1) porous ceramic skeleton
多孔陶瓷骨架
1.
In order to make full use of the advantages of both metals and ceramics and avoid their disadvantages,a two-continuous-phase-of-metal/ceramic composite was prepared by pressure-infiltration of metal into porous ceramic skeleton,which was rarely reported.
为了充分发挥陶瓷和金属的各自优势 ,同时避免它们的各自劣势 ,文章采用鲜有报道的多孔陶瓷骨架压渗工艺制备双连续相金属 /陶瓷复合材料。
2) porous ceramic scaffold
多孔陶瓷支架
1.
The calcium phosphate porous ceramic scaffolds with high porosity for the bone tissue engineering were fabricated by the foam impregnation technology,and the composite scaffolds composed of ceramic and gelatin were gained by coating the porous ceramic samples with gelatin solution.
采用有机泡沫浸渍工艺制备了高孔隙率的钙磷多孔陶瓷支架,将多孔陶瓷样品浸于明胶溶液中渗涂得到陶瓷/明胶复合支架;采用复合明胶涂层的方法对钙磷多孔陶瓷支架进行增强处理,在不破坏多孔支架孔隙特征的情况下,成功地在样品的孔壁上复合了明胶涂层。
3) porous ceramic
多孔陶瓷
1.
Fabrication of Porous Ceramic With Starch as the Pore-forming Agent;
以淀粉作造孔剂制备多孔陶瓷
2.
Preparation of TiO_2 porous ceramic;
TiO_2多孔陶瓷的制备
3.
Al_2O_3 matrix porous ceramics prepared by SHS;
燃烧合成法制备的Al_2O_3基多孔陶瓷
4) porous ceramics
多孔陶瓷
1.
Preparation and development of porous ceramics;
多孔陶瓷制备技术的进展
2.
Fabrication of porous ceramics using polymeric sponge dipping method;
有机泡沫浸渍法制备多孔陶瓷
3.
Research on fabrication of warp-knitted space porous ceramics by impregnation process;
由浸渍工艺制备经编间隔结构多孔陶瓷的研究
5) porous ceramic membrane
多孔陶瓷膜
1.
CFD modeling of permeate process in 19-channel porous ceramic membranes;
19通道多孔陶瓷膜渗透过程的CFD模拟
2.
According to the urgent demand of deep treatment in dyeing wastewater,this paper studied the advanced treatment of dyeing wastewater by new type combined porous ceramic membrane reactor,which include the new type moving bed bioreactor and porous ceramic technology.
本文针对印染废水急需深度处理的现状,对新型多孔陶瓷膜组合反应器深度处理印染废水一级出水进行了研究,反应器采用新型移动床生物膜处理加多孔陶瓷膜的组合工艺,为工程上应用提供参考。
6) porous SiC ceramics
SiC多孔陶瓷
1.
The porous SiC ceramics were prepared by vacuum sintering in this investigation,the effect of different sintering aids,Al2O3-Y2O3 and Si,and different pore formers,acrylamide copolymer and Carboxymethyl Cellulose(CMC) on the microstructures and porosity were studied.
采用真空烧结方法制备了SiC多孔陶瓷,研究了不同助烧结剂Al2O3-Y2O3、Si以及不同造孔剂丙烯酰胺聚合物、羧甲基纤维素(CMC)对SiC多孔陶瓷形貌和气孔率的影响。
2.
Properties of the two kinds of porous SiC ceramics using PCS and SR as binder respectively were analyzed and compared.
分别以聚碳硅烷和硅树脂作粘结剂,SiC微粉作骨料,在惰性气氛中1000℃下低温制备出SiC多孔陶瓷,所得样品的气孔率在43%～52%之间,抗断裂强度最高达到了18。
3.
The flexural strength of porous SiC ceramics increased with increasing PCS content and shaping pressure,while decreased with increasing the carbon content.
以聚碳硅烷为粘接剂,SiC粉末为骨料,经模压成型、惰性气氛保护下于1000℃裂解低温制得SiC多孔陶瓷。
补充资料：多孔磷酸钙生物陶瓷
分子式：
CAS号：
性质： 是一种含活体细胞的骨替换材料。生物陶瓷为其提供良好的生物相容性和骨传导性；骨髓细胞作为其成骨细胞的源，赋予材料骨诱导性。可用于长骨段缺损的修复。
CAS号：
性质： 是一种含活体细胞的骨替换材料。生物陶瓷为其提供良好的生物相容性和骨传导性；骨髓细胞作为其成骨细胞的源，赋予材料骨诱导性。可用于长骨段缺损的修复。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条