1) temperature drop
钢液温降
1.
The results provide a theoretical basis for decreasing the temperature drop and the tapping temperature of molten steel in the converter and for formulating proper temperature system of liquid steel.
全文通过对钢包建立合理的数学模型 ,对其吹氩行为进行模拟 ,分析了不同情况下钢液温降行为 ,为减少钢液温降、降低出钢温度、合理制定钢包的温度制度提供了一定的依
2) liquid steel
钢液
1.
Effect of B_2O_3 and Al_2O_3 in slag on nitrogen content in liquid steel;
中间包覆盖渣中B_2O_3和Al_2O_3对钢液氮含量的影响
2.
Flow Control Technology and Flow Feature of Liquid Steel in Tundish for Concasting;
连铸中间包内钢液流动特性及控流技术
3.
Study on dephosphorization rate of liquid steel in secondary refining process by CaO-based fluxes;
CaO基熔剂对钢液二次精炼脱磷速度的研究
3) molten steel
钢液
1.
Study of probe material for ultrasonic treatment of molten steel;
超声波处理高温钢液的工具头材质研究
2.
The effect of continuous casting tundish mantle material on carbon content of molten steel;
连铸中间包覆盖剂对钢液含碳量的影响
4) steel melt
钢液
1.
Solid electrolyte, electronic conduction materials and deoxidizer are integrated to make into a deoxidization unit which is used in examination of the unpolluted deoxidization without inclusion for steel melts.
将固体电解质、高温电子导电材料及脱氧剂集为一体,构成脱氧单元,用于钢液的无夹杂污染脱氧研究。
2.
The result showed that the copper content (mass fraction)in steel melt of 400g was reduced from about 0.
在1600℃、常压Ar气氛下，向钢液中分别加入NH4及（NH4)2C2O4，将400g钢水含铜量从0。
3.
The results show that the copper content(mass fraction) in steel melt is reduced from 0.
提出了用喂丝法向钢液中插入铵盐或氨基化合物的脱铜方法。
5) Molten Steel Flow
钢液流动
1.
The effect of opening at the bottom of submerged entry nozzle on molten steel flow and temperature distribution in crystallizer;
浸入式水口底部开孔对结晶器内钢液流动和温度分布的影响
2.
According to the actual production condition of RH-MFB in one plant,the coupling mathematic model of molten steel flow and carbon concentration distribution in ladle is established by using the commercial code CFX.
根据某厂RH-MFB的生产实际,采用CFX软件建立钢包内钢液流动与碳浓度分布的耦合数学模型,对钢液的流动特性以及碳浓度的分布情况进行研究,利用现场数据验证所建模型,分析了脱碳后期钢液碳浓度的分布情况,考察了工艺设备等因素对脱碳处理过程的影响,为超低碳钢的工艺优化提供理论依据和指导。
3.
The molten steel flow in slab continuous casting mould and the effect of the nozzle exit inclined angle,immersion depth and casting speed have been introduced,and the flow pattern of molten steel in the curved mould of billet has been generalized as well.
介绍了板坯连铸结晶器中的钢液流动和水口出口倾角、水口浸入深度及浇铸速度等参数对流动行为的影响，同时概括了小方坯弧形结晶器中钢液流动特点。
6) Low Carbon Molten Steel
低碳钢液
参考词条
补充资料：降液管清液层高度
分子式：
CAS号：
性质：又称降液管清液层高度。板式塔降液管内的液柱液面到下层塔板的垂直距离。如图中的Hd（图暂缺）。为保持板式塔正常操作，避免发生液泛，降液管液柱高度不能超过一定限度。一般应满足Hd≤(0.4～0.6)(HT+hw)，式中HT为塔板间距，hw为堰高，系数一般取0.5，易起泡物系取0.4，不易起泡物系取0.6。
CAS号：
性质：又称降液管清液层高度。板式塔降液管内的液柱液面到下层塔板的垂直距离。如图中的Hd（图暂缺）。为保持板式塔正常操作，避免发生液泛，降液管液柱高度不能超过一定限度。一般应满足Hd≤(0.4～0.6)(HT+hw)，式中HT为塔板间距，hw为堰高，系数一般取0.5，易起泡物系取0.4，不易起泡物系取0.6。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。