1) Velocity of corrosion
熔蚀速度
2) melting speed
熔化速度
1.
Study on melting speed of continuous casting mold powder;
含碳材料对连铸保护渣熔化速度影响的研究
2.
The burning loss of carbon is a key factor that controls the melting speed of mold powder.
利用碳烧损量是控制保护渣熔化速度的关键因素这一原理,用失重法检测了不同温度下保护渣的烧损量并尝试用于比较其熔化速度。
3.
The melting speed of low carbon CC mold flux composed of different carbon materials(graphite and active carbon) and different carbon mass fraction((2.
2%)的低碳连铸保护渣在空气中和在氩气中的熔化速度,结果是在有惰性气体保护下的熔化速度远小于一般在空气中的熔化速度。
3) deposition rate
熔敷速度
1.
The effects of proportion of mixed gas, welding current, arc voltage and gas flow rate of mixed gas shielded arc welding of flux cored wire on the deposition rate, deposition coefficient and deposition efficiency were studied with shielding gas of Ar+CO2.
以Ar+CO2作为保护气体,研究了药芯焊丝混合气体保护焊的混合气体配比、焊接电流、电弧电压和气体流量对熔敷速度、熔敷系数和熔敷效率的影响。
2.
It is presented preliminary assessment of new plasma technology with both high deposition rate and low rate of dilution ,which was developed under the calculation and analysis of compressive properties of plasma are, arc flame characteristics and kinematics behavior of poweder in the arc.
人们衡量堆焊方法一般总是从两个方面进行 ,一是熔敷速度 ,二是稀释率。
3.
The Influence of powder feeding mode on the deposition rate was emphatically analyzed here.
介绍了目前等离子弧粉末堆焊常用的几种送粉形式 ,较详细地分析了其利弊 ,着重分析了送粉方式对粉末熔敷效率的影响因素 ,并通过大量分析及实验验证 ,给出了同时获得高熔敷速度低稀释率的最佳送粉形
4) Melting rate
熔化速度
1.
Practice of Raising Melting Rate of Medium Frequency Coreless Induction Furnace;
提高中频无芯感应电炉熔化速度的实践
2.
In the process of trail-producing powder,that the carbon affects the melting rate of powder can be showed by the thermal characteristic apparatus.
在保护渣的研制中,通过使用热特性仪,能够有规律的反映炭质材料对保护渣的熔化速度的控制效应,故提出一种用热特性仪测试保护渣熔化速度的测定方法。
3.
C+BN skeleton particles can decrease viscosity,melting temperature,melting rate and crystallizing temperature of the mold powder.
C+BN作为骨架粒子可以使保护渣的粘度减小、熔化温度降低、熔化速度降低、结晶温度降低。
5) melting casting rate
熔铸速度
6) smelting speed
熔炼速度
1.
Determination of fuming furnace smelting speed and deoxidization terminal;
烟化炉熔炼速度及还原终点的判定
补充资料：熔盐电解法生产铌粉(见熔盐电解法生产钽粉)
熔盐电解法生产铌粉(见熔盐电解法生产钽粉)
production of niobium powder by molten salt electrolysis
rongyand+onjlefa ShengChan n.fen熔盐电解法生产妮粉(produetion。fn;obi-um powder by molten salt eleetrolysls)见熔盐电解法生产担粉。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条