1) austenite shell
奥氏体壳
1.
It was pointed out that degeneration of spheroidal graphite always takes place during growing process of the graphite, and always results from the break of its austenite shell which is caused by various factors.
指出球状石墨畸变都是在石墨长大过程中,由于各种因素引起奥氏体壳破裂而造成的。
2.
The high temperature solidification structure in hypereutectic nodular iron has been showed clearly by the color etching technique and the formation mechanism of the austenite shell (the austenite shell is a part of the austenite dendrites) around the nodular graphite has been observed and analyzed.
采用着色腐蚀技术 ,可清晰地显示出过共晶球墨铸铁中的高温凝固组织 ,观察分析了石墨球周围奥氏体壳 (奥氏体壳是奥氏体枝晶的一部分 )的形成机制。
2) austenitic
[英][,ɔ:stə'nitik] [美][,ɔstə'nɪtɪk]
奥氏体
1.
Surface Quality Control of Cold Rolled Austenitic Stainless Stell Strip for Deep Drawing;
冲压用冷轧奥氏体不锈钢带的表面质量控制
2.
Supersonic detection for welding joint of austenitic stainless steel small-diameter pipe;
奥氏体不锈钢小径管焊缝超声波检测
3.
Inspection detection research in austenitic stainless steel with different ultrasonic probes;
奥氏体不锈钢焊接接头超声波检测研究
3) austenite steel
奥氏体钢
1.
The interface lattice misfitting theory can not explain that TiC and CaS act as an efficient catalyzer during the non-equilibrium solidification of austenite steel.
利用界面共格对应理论无法解释奥氏体钢非平衡凝固过程中TiC、CaS为奥氏体枝晶有效异质核心的现象。
2.
The performance of granular γ+(Fe,Mn)3C eutectics reinforced austenite steel matrix composites (EAMC) was studied, and the strengthening/toughness match and wear resistance were analyzed.
在研究团球γ+(Fe,Mn)3C共晶体增强奥氏体钢基自生复合材料(EAMC)的力学与耐磨性能的基础上,分析了EAMC的强韧化及耐磨机理。
3.
The effect of sliding velocity on the friction behaviors of in situ granular 7+(Fe, Mn)3C eutectics reinforced austenite steel matrix composites (EAMC) has been investigated by the pin-on disc dry sliding tests and scanning electron microscopy (SEM) observation.
利用MPX-2000型主轴盘销式磨损实验机和扫描电子显微镜(SEM)研究了相对滑动速度对团球γ+(Fe,Mn)_3C共晶体增强奥氏体钢基自生复合材料(EAMC)摩擦学性能的影响。
4) austenizing
奥氏体化
1.
The quenching microstructure of low carbon steel after austenizing with and without DC electric field was studied.
研究了低碳钢在直流静电场中进行奥氏体化后淬火的显微组织。
2.
From the mechanics of steel austenizing ,a mathimatic model of austenizing process is set up.
从钢的奥氏体化机理入手，建立了加热奥氏体的数学模型；并对激光加热温度场和硬化带进行了估算。
3.
The microstructure of 45CrMoV steel after austenizing followed by air cooling and tempering at various temperatures have been studied, using TEM and SAD.
利用透射电镜和选区电子衍射研究了45CrMoV钢奥氏体化后空冷及其在不同温度回火的显微组织。
5) austenitic steel
奥氏体钢
1.
The direct relationship between stacking fault energy and phase transformation driving force of austenitic steels and the effect of stacking fault energy and strain energy on the morphology of martensite are deduced.
导出了在奥氏体钢中相变驱动力与层错能的关系以及层错能和应变能对马氏体形态的影响规律。
2.
The effects of stacking fault energy and strength on phase transformation in cryogenic austenitic steels were studied.
研究了低温奥氏体钢中层错能和强度对相变的作用 ,导出了相变临界分切应力和层错能与强度之间的关系式。
6) austenization
奥氏体化
1.
Effects of Nb on the austenization and static recrystallization behavior of 20MnSi steel;
铌对20MnSi钢奥氏体化和静态再结晶的影响
2.
Simulation of austenization during intercritical annealing for Fe-C-Mn cold rolling dual phase steel;
Fe-C-Mn系冷轧双相钢两相区奥氏体化过程模拟
3.
In this paper the quenching microstructure of the low carbon steel in the austenization with the application of an electric field 20kV/cm between the specimen and a companion electrode of an electrostatic circuit is studied.
研究了电场奥氏体化对低碳钢的淬火组织的影响。
补充资料：奥氏体-贝氏体球铁
分子式：
CAS号：
性质：又叫奥-贝球铁。基体组织为奥氏体加贝氏体组织的球墨铸铁。这类球铁硅含量一般在1.4%～3.8%。含锰量小于0.5%，与普通球铁比较硅偏高、锰偏低。通过调节化学成分与热处理获得理想的奥-贝球铁的基体组织为针状贝氏体或无碳贝氏体一富碳奥氏体。这类球铁具有优良的综合机械性能、强度高、耐磨性好、韧性好、特别是有高的缺口韧性，可代替钢，用于制作重要受力结构件，如曲轴、齿轮、凸轮轴等。
CAS号：
性质：又叫奥-贝球铁。基体组织为奥氏体加贝氏体组织的球墨铸铁。这类球铁硅含量一般在1.4%～3.8%。含锰量小于0.5%，与普通球铁比较硅偏高、锰偏低。通过调节化学成分与热处理获得理想的奥-贝球铁的基体组织为针状贝氏体或无碳贝氏体一富碳奥氏体。这类球铁具有优良的综合机械性能、强度高、耐磨性好、韧性好、特别是有高的缺口韧性，可代替钢，用于制作重要受力结构件，如曲轴、齿轮、凸轮轴等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条