1) Centrifugal granulation
离心制粒
2) centrifuging
离心
1.
Study on The Microstructure of Intermetallic Compound-ceramic Lining in Composite pipe Prepared by SHS-centrifuging;
自蔓延—离心法制备金属间化合物/陶瓷内衬复合钢管的实验研究
3) centrifuge
离心
1.
Experimental research on the combined centrifuge-aerofoil grain cleaning fan;
离心—轴流组合式清粮风机的试验研究
2.
Effect of Centrifuge and Frozen Treatment on Chaetoceros muelleri Culture;
离心·冷藏对牟氏角毛藻再培养的影响
3.
On the base of sodium hydroxide and zinc acetate to adsorb the sulfide and the sodium borate buffer added to enhance the deposition effect,the deposition of zinc hydroxide and zinc sulfide was separated from the solution by a centrifuge,then the soluble sulfide was determined by the method of methylence blue.
在Zn(CH3COO)2和NaOH溶液固定硫化物和硼砂缓冲液加强沉淀效果的基础上,提出用离心法将硫化物从溶液中分离出来,采用亚甲基蓝法测定水样中硫化物浓度的方法。
4) centrifugation
离心
1.
Preparation of porous alumina ceramic with uniform cell size by centrifugation-template method;
离心成型结合模板法制备孔径均匀的多孔氧化铝陶瓷
2.
Aqueous enzymatic extraction of walnut oil:enzymatic hydrolysis and centrifugation;
水酶法提取核桃油工艺研究——酶解和离心参数确定
3.
K526 cell exosomes isolated by a sequence of differential centrifugation steps;
多步离心法提取K526细胞外泌体
5) centrifugal
离心
1.
Study of centrifugal high-speed chromium plating;
离心高速电镀铬工艺研究
2.
The Microstructure of Intermetallic Compound-ceramic Lining in Composite Pipe Prepared by SHS-centrifugal;
SHS-离心复合钢管金属间化合物-陶瓷内衬的显微组织
3.
Heavy Compound Ductile Iron Work Roller Manufacturing by Centrifugal Casting;
离心复合大断面球墨铸铁轧辊的制造
6) Centrifugalization
离心
1.
Isolation of exosomes derived from dendritic cells by ultrafiltration centrifugalization and their morphologic characteristics;
树突状细胞胞外体(Exosome)的超滤离心法提取及形态观察
2.
METHODS:Bulleyaconitine multivesicular liposomes and its free bulleyaconitine were separated by centrifugalization.
方法:采用离心法分离草乌甲素多囊脂质体,HPLC测定总药量和游离草乌甲素量并计算样品包封率。
3.
Consequently, after centrifugalization for over 6 minutes, the background was very clean and no HBeAg false positive reaction was found.
方法 :标本分别采用 30 0 0 rpm离心 0 ,6 ,9,12 ,15 ,18m in,取上清液检测。
参考词条
补充资料：FL系列沸腾制粒干燥机
  应用： 制药工业中的造粒：片剂颗粒、冲剂颗粒、胶囊剂颗粒。 食品工业的造粒：可可、咖啡、奶粉、颗粒果汁、调味品等。 其它行业的造粒：农药、饲料、化肥、颜料、染料化工等 粉状或颗粒状湿物料的干燥。 包衣：颗粒、丸剂保护层、备色、缓释、薄膜、肠溶包衣等。 特点： 通过粉体造粒，改善流动性，减少粉尘习扬； 通过粉体造粒改善其溶解性能； 混合、制粒、干燥在一机内完成一步法制粒； 采用抗静电滤布，设备操作安全； 设置压力泄放孔，一旦发生爆炸，设备人员不受伤害； 设备无死角，装卸料轻便快速，冲洗干净，满足GMP规范 工艺流程图：  原理： 物料粉末粒子，在原料容器（流化床）中呈环形流化状态，受到经过净化后的加热空气预热和混合，将粘合剂溶液雾化喷入，使若干粒子聚集顾含有粘合剂的团粒，由于热空气对物料的不断干燥，使团粒中水分蒸发，粘合剂凝固，此过程不断重复进行地，形成理想的、均匀的多微孔球状颗粒。 技术参数：
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。