1)  inner lining board
内衬板
1.
A sort of the special material for the inner lining board with good performance and low cost for the light vehicle had been made by blending propylene copolymer, LLDPE, POE and talc etc.
采用共聚聚丙烯、线性低密度聚乙烯、(乙烯/辛烯)共聚物和滑石粉等混合后经双螺杆挤出机造粒,制备了一种性能优异、成本低廉的轻型汽车车门内衬板专用料,性能满足五十铃系列轻型车的要求,已经应用在多种型号的轻型汽车上。
2)  inner door scaleboard
门内衬板
1.
Through analysis to technology of embedded inner door scaleboard of disinfectant box, the die processes are determined and some questions are further analyzed in test.
通过对嵌入式消毒柜门内衬板的工艺分析 ,确定其模具加工方案 ,同时对试模过程中存在的问题作进一步的剖析。
3)  automobile interior lining board
汽车内衬板
4)  lining
内衬
1.
The Cause and Countermeasure for Early Dilapidation of 240kA Prebaked Anode Cell's Lining;
240kA预焙槽早期内衬破损的原因及对策
2.
Application to engineering of lining turnover repair technique of CIPP hoses without excavation;
CIPP树脂软管翻转内衬非开挖修复技术应用
3.
The paper introduced the development status of lining materials of dense medium cyclone both in China and overseas and made prospect for the each new type of ceramics material used as lining of dense medium cyclone.
介绍了当前国内外重介质旋流器内衬材料的发展现状,并对各种新型陶瓷用作重介质旋流器内衬材料的发展前景进行了展望。
5)  inner lining
内衬
1.
Installation method of pipeline plastic film inner lining;
管道塑膜管内衬施工方法
2.
This paper expounds the feasibility and theoretical basis of using KMTBCr28 wear resistant material to replace the SiC inner lining in three-product cyclone,and analyzes the application prospect of this kind of material.
阐述了以KMTBCr28耐磨材料取代三产品旋流器SiC内衬的可能性和理论依据,分析了这种材料的应用前景。
3.
This paper analyzes the thermal expansion problems of inner lining of two 450 t/h CFB boilers in technical renovation project of Baoding Cogeneration Power Plant, and proposes improving schemes based on actual field conditions.
对保定热电厂技改工程2×450t/hCFB锅炉内衬炉墙在热膨胀方面存在的问题及原因进行了分析,并结合现场实际情况进行计算,提出了改进方案。
6)  liner
内衬
1.
Discussion on preventing the dropping of liner of heating agent furnace;
防止热媒炉内衬脱落的探讨
2.
Focusing on failures frequently occurring to liners of dry bottom hoppers,the unreasonableness of its construction,poor cooling,the casting technique used and effects of other parts are being analyzed.
针对锅炉冷灰斗内衬经常损坏的情况,分析了原来冷灰斗内衬结构不合理、冷却不良、浇注工艺及设备部件方面的原因,提出了相应的改造措施,列举了改造的效果。
3.
The structure analysis of the filament-wound cylinder pressure vessel with internal liner are performed.
对具有内衬的纤维缠绕圆筒压力容器进行了结构分析。
参考词条
补充资料:衬经衬纬圆纬机
      用以编织衬经衬纬针织物的圆型纬编针织机。它在编织平针组织的同时,衬入不参加成圈的经纱和纬纱,形成衬经衬纬针织物。其基本组织结构如图1所示。 这种针织物的纵向和横向的延伸度都较小,具有机织物的特性,除适合做各种外衣外,还可作灌溉用涂塑管道的骨架。在衬经衬纬圆纬机上,有三组纱线:衬经纱、衬纬纱、成圈纱参加编织。其编织机构如图2所示。
  机器的针筒固定在台面上,三角座相对于针筒回转。衬经纱从固定的纱架上引出,通过分经盘(或导经片)由上而下经过针间衬入织物线圈纵行间。所有衬经纱从针筒口向外倾斜一定角度,形成圆锥面,便于成圈纱的喂入。衬纬纱筒子架位于衬经纱外侧,与三角座一起回转,通过导纬器将纬纱衬入针背与经纱之间,依次横向搁在针上的旧线圈上方。成圈纱筒子架位于衬经纱内侧,与三角座同步回转。导纱器处于织针与衬经纱之间,把成圈纱喂入针钩内编织成圈,形成平针组织,同时,使其线圈的沉降弧从内侧包住衬经纱,圈柱从外侧包住衬纬纱,从而使三组纱线结合在一起,形成一种基本的衬经衬纬针织物。  衬经衬纬针织物用于外衣产品时,由于衬经纱和衬纬纱之间没有交织点,易于拱出,因此,需改变其组织结构。例如,通过导经片将衬经纱在针头上绕一圈,并把它向下转移到旧线圈处,再和旧线圈一起向上套圈,使衬经纱与成圈纱结合得更紧密。另外,适当加粗衬纬纱,也可提高衬经衬纬针织物的结构稳定性。
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。