1) lining erosion
内衬蚀损
1.
Due to the inherent limitation of the traditional methods to measure lining erosion state of reaction tower of copper flash furnace, a new non-contacting real-time monitor method and corresponding analysis and diagnostic system are provided in this paper.
针对铜闪速炉反应塔内衬蚀损状况检测的传统方法所存在的局限性,提出了一种基于红外点温仪在线扫描识别反应塔内衬蚀损的非接触实时监测的新方法,并设计了一套相应的监测诊断系统。
2) lining
内衬
1.
The Cause and Countermeasure for Early Dilapidation of 240kA Prebaked Anode Cell's Lining;
240kA预焙槽早期内衬破损的原因及对策
2.
Application to engineering of lining turnover repair technique of CIPP hoses without excavation;
CIPP树脂软管翻转内衬非开挖修复技术应用
3.
The paper introduced the development status of lining materials of dense medium cyclone both in China and overseas and made prospect for the each new type of ceramics material used as lining of dense medium cyclone.
介绍了当前国内外重介质旋流器内衬材料的发展现状,并对各种新型陶瓷用作重介质旋流器内衬材料的发展前景进行了展望。
3) inner lining
内衬
1.
Installation method of pipeline plastic film inner lining;
管道塑膜管内衬施工方法
2.
This paper expounds the feasibility and theoretical basis of using KMTBCr28 wear resistant material to replace the SiC inner lining in three-product cyclone,and analyzes the application prospect of this kind of material.
阐述了以KMTBCr28耐磨材料取代三产品旋流器SiC内衬的可能性和理论依据,分析了这种材料的应用前景。
3.
This paper analyzes the thermal expansion problems of inner lining of two 450 t/h CFB boilers in technical renovation project of Baoding Cogeneration Power Plant, and proposes improving schemes based on actual field conditions.
对保定热电厂技改工程2×450t/hCFB锅炉内衬炉墙在热膨胀方面存在的问题及原因进行了分析,并结合现场实际情况进行计算,提出了改进方案。
4) liner
内衬
1.
Discussion on preventing the dropping of liner of heating agent furnace;
防止热媒炉内衬脱落的探讨
2.
Focusing on failures frequently occurring to liners of dry bottom hoppers,the unreasonableness of its construction,poor cooling,the casting technique used and effects of other parts are being analyzed.
针对锅炉冷灰斗内衬经常损坏的情况,分析了原来冷灰斗内衬结构不合理、冷却不良、浇注工艺及设备部件方面的原因,提出了相应的改造措施,列举了改造的效果。
3.
The structure analysis of the filament-wound cylinder pressure vessel with internal liner are performed.
对具有内衬的纤维缠绕圆筒压力容器进行了结构分析。
5) lining material
内衬材料
1.
Determination of thermal conductivity of new lining materials in aluminum reduction cells;
铝电解槽新型内衬材料导热系数的测量
2.
Conclusion is made that the lining material of the domestic pilling box is different from the imported pill.
针对滚箱式起球仪箱体内衬材料的特性会直接影响到织物的起球测试结果,分析了软木材料良好的摩擦特性及内衬材料的制作过程。
3.
Stringent requirements,of properties and of handling of abrasion and heat resistant lining materials,are asked for by circulating fluidized bed boilers.
CFB锅炉对耐火耐磨内衬材料的性能、施工提出了严格的要求,而内衬材料的烘干过程直接关系到施工质量和材料性能。
6) cement lining
水泥内衬
参考词条
补充资料：内损
内损 内损 病名。因外伤引致肢体深部组织或脏腑损伤者。见《诸病源候论》卷三十六，或名内伤。该书称：“此为人卒被重物压迮，或从高处坠下，致吐下血，此伤五内故也。”《外台秘要》引《广济方》“疗从高坠下，内损瘀血”，“近效疗堕马内损”之论。究其病因，不外高处坠下、重物压迮、外力挤撞等类，或伴表伤并不严重，而内损则十分明显，或由于内因所成者。内损多发于胸腹内脏，一般有伤气、伤血、伤脏腑之区别。若伤处肿痛不明显，痛无定处则为伤气；若伤处疼痛显著，皮色发红或青紫，甚则血溢妄行，出现发热、寒战、呕吐、便血、尿血、咳血等症者为伤血；若胸胁或腹中疼痛剧烈，伴有昏厥、吐血、便血等症者为伤脏腑。若伤头部，损及脑髓，则症见头晕目眩，额部有冷汗，言语不清，恶心呕吐，甚至口眼斜。治宜辨伤之部位轻重，以其所伤，或手法外治、或服药内治。若伤气者，宜服复元通气散；伤血重者，或损及内脏，则以活血化瘀为佳，可服桃仁承气汤。参见伤气、伤血、伤脏腑、脑骨伤等各条。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。