1)  water distribution module
喷淋管
1.
, and made the secondary water distribution module to be realized accurately, resulting in the improvement of billet quality accordingly.
分析认为 ,主要是冷却水水质差、水温高、喷淋管结垢多导致的水流速度慢、易形成气堵等原因造成的。
2)  deluge distribution piping
喷淋管线
1.
When the deluge valve installed on the offshore oil and gas production facility fire water system is suddenly closed,the deluge distribution piping will generate water hammer effect.
海上油气生产设施消防喷淋管线,在喷淋阀突然关闭时会产生水锤效应。
3)  spraying
喷淋
1.
Performance analysis of flow and heat transfer of spraying cooling for converter gas with high temperature in Venturi tube;
转炉高温烟气除尘文氏管喷淋降温流动与传热性能分析
2.
Numerical Simulation of Temperature Decrease and Fluid Flow With Water Spraying in Venturi Tube of Converter Coal Gas Recovery System;
转炉煤气回收系统文氏管喷淋降温与流动数值模拟
3.
The paper describes that the quality improving of continuously cast square billet、 decreasing of steel-leaking、 fastening of casting speed and enhancing of economic benefit are the result of the improvement of the second cool-down spraying for continuous casting machine.
本文介绍广钢转炉炼钢厂通过对连铸机二冷喷淋方式进行改进后,提高了连铸坯的质量,减少漏钢,提高 拉速,取得了一定的经济效益。
4)  spray
喷淋
1.
The New Air-Cleaning Equipment with Water Spraying Upward and Drops Second Fining Process;
新型的上喷淋再细化水洗气体净化设备
2.
Design Summarization for Conveyor Type Spray-cleaning Machine;
输送链式喷淋清洗机的设计概述
3.
Flow field was used for analysis of spray,and result showed that liquid.
分析了液体洗涤油烟净化技术的原理、水循环利用时对洗涤废液进行的油水分离,提出了采用流场分析喷淋,以了解其流场的特性。
5)  shower
喷淋
1.
The shower facilities in press section of high speed paper machine and water conservation technology;
高速纸机压榨部喷淋设备与节水技术
6)  spraying width
喷淋宽度
1.
The process characteristics include a new control method,which eliminated the on-off-on water spraying;the spraying width varied with the slab width;the number of the cooling zone and loop,and the length of the narrow spraying zone increased;almost all the zone used air-water cooling spray nozzles,etc.
工艺特点:新的控制方法消除了间隙喷水,喷淋宽度随板坯宽度变化,冷却区数量及回路数量增加,窄边喷淋区长度增加,几乎全部采用气水冷却喷嘴等。
参考词条
补充资料：喷淋式蛇管换热器
分子式：
CAS号：

性质：蛇管式换热器一种。蛇管外面用冷水喷淋，管内的流体即被冷却或冷凝。所以又可称为喷淋式冷却器或喷淋式冷凝器。蛇管是由用U形肘管相互连接的直管构成。冷却水由管上方的水槽均匀淋下。与沉浸式比较，主要优点是：（1）传热效率较高；（2）结构较简单；（3）材料消耗较少；（4）成本较低；（5）便于检修和清洗。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。