1) weld bending strength
焊缝抗弯强度
2) weld strength
焊缝强度
1.
In addition,the weld strengths of different weld width and type are determined by uni.
另外还进行了织物膜材在单轴拉伸状态下的焊缝强度试验,测定和对比了不同焊接方式和宽度的焊缝强度,建议单面对接焊缝宽度不应小于50mm,搭接不应小于30mm。
3) bending strength
抗弯强度
1.
The detecting system of stress wave velocity for laminated veneer lumber bending strength based on single chip;
基于单片机的单板层积材抗弯强度应力波波速检测系统
2.
Analysis on bending strength of PcBN composite;
PcBN复合片抗弯强度的分析
3.
Effect of pore-forming agents content on bending strength of SiC/Al composites;
造孔剂含量对SiC/Al复合材料抗弯强度的影响
4) bend strength
抗弯强度
1.
Application of artificial neural network method in prediction of bend strength of welded joint;
ANN在焊接接头抗弯强度预测中的应用
2.
In the prouduction of (WC15Ni ) non-magnetic Cemented Carbide we can improve the bend strength by choosing the high quality WC which has narrower range of particle size distribution and adding moderate Cr3C2.
在WC15Ni无磁硬质合金生产过程中,选用粒度分布范围较窄的优质WC以及添加适量的Cr3C2,促进了抗弯强度的提高。
3.
It is showed from the result that with an appropriate amount of addition of above alloy powder the hardness and bend strength of copper alloy are both raised: when addition being as 1.
研究了富镧稀土-Ni合金粉在铜合金中的作用,结果表明铜合金中添加适量的富镧稀土-Ni合金粉,硬度、抗弯强度等有很大提高。
5) flexure strength
抗弯强度
1.
The result shows that weak-bonding interface will do n 't reduce the flexure strength of ceramics with reasonable design.
介绍了弱界面结合材料的研究体系和力学性能的研究现状,重点分析了弱界面结合对陶瓷材料抗弯强度的影响及弱界面结合陶瓷材料的增韧机制。
2.
Its workability, mechanical property and durability, especially the flexure strength and permeability resistance are apparently increased, its utility range can be widened and its useful life prolonged.
文章在试验的基础上，研究聚合物丙乳和硅粉对高强混凝土各项性能的影响，从而配制出一种以聚合物丙乳和硅粉为改性材料的新型高性能混凝土，该混凝土的工作性、力学性能和耐久性，尤其是抗弯强度、抗渗性得到明显提高，拓宽了使用范围，增加了使用年限。
3.
The effects of oxygen,nitrogen,carbon content and their configuration and surfacedamage on flexure strength of silcon wafer at room-temperature have been investigatedthrough experiments.
通过实验系统地研究了硅中氧、氮、碳含量和状态以及硅片表面损伤对室温下硅片抗弯强度的影响规律，讨论了室温抗弯强度与高温抗形变能力之间的内在联系，提出了室温抗弯强度大小可以反映硅片高温抗形变能力的观点。
6) flexural strength
抗弯强度
1.
Evaluate the effect of different heat-cure time on the flexural strength of the resins reinforced by potassium titanate whiskers
热处理时间对钛酸钾晶须增强牙用复合树脂的抗弯强度的影响
2.
Compare the flexural strength of dental composite resins reinforced by potassium titanate whiskers with two commonly used composites
钛酸钾晶须增强的复合树脂与两种常用复合树脂的抗弯强度的比较
3.
The effects of different crystallization time on the crystal performance,the microstructure and the flexural strength of glass-ceramic of the MgO-Al2O3-SiO2 system were studied by differential thermal analysis(DTA),X-ray diffraction(XRD) and scanning electron microscopy(SEM).
通过差热分析(DTA)、X射线衍射分析(XRD)、扫描电子显微镜(SEM)等测试手段研究了不同晶化时间对MgO-Al2O3-SiO2系微晶玻璃析晶性能、微观结构及抗弯强度的影响。
补充资料：抗弯强度
分子式：
分子量：
CAS号：
性质：见弯曲强度。
分子量：
CAS号：
性质：见弯曲强度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条