1) Segmented condensation
分段冷凝
2) divided evaporator and condenser
分段蒸发和冷凝
3) Condensation segment
冷凝段
1.
The heat transfer and flow pass condensation segment in the gravity heat pipe with inner screw thread were investigated.
分析了在重力热管内加内螺纹的方法 ,研究了重力热管的冷凝段的传热及流动状况 。
4) subsection cooling
分段冷却
1.
Effect of subsection cooling process on banded structure of C-Mn plate has been studied by industrial tests.
通过工业试验,研究了分段冷却工艺对C-Mn钢中板带状组织的影响,分析了带状组织的产生机理。
2.
This article introduces the principle of subsection cooling control of rolling oil,it also discusses the controlling method of roller thermal crown and meaning of the parameter controllin
介绍了轧制油分段冷却控制的原理 ,论述了轧辊热凸度的控制方法以及控制参数的意
3.
During controlled cooling,not only start cooling temperature affects mechanical properties of test steel,but also subsection cooling mode can increase mechanical properties of test steel.
在控制冷却过程中,除开始冷却温度对试验钢的性能影响较大外,分段冷却工艺参数对试验钢性能的提高也起很大作用。
5) freeze-dephlegmation
冷冻分凝
1.
Application of freeze-dephlegmation to bromamine acid aqueous solution purification;
冷冻分凝原理处理溴氨酸水溶液方法初步研究
2.
Freeze-dephlegmation: Application to Bromamine Acid Aqueous Solution Purification and the Practical Wastewater Discharged for Ullmann Condensation Reaction;
利用冷冻分凝原理处理废水,是一项开发自然能源、消除环境污染的有益工作。
6) partial condensation
部分冷凝
1.
A calculation procedure of the process condition on the separation of the heavy component from natural gas by partial condensation is presented,and the influence of temperature and pressure on the separation of the heavy component is analysed.
介绍了天然气部分冷凝除重组分工艺条件的计算方法 ,并分析了温度、压力对除重组分的影响规律。
补充资料：东汉分段锦铜马
东汉分段锦铜马 东汉时期铜制品。1975、1976年，贵州兴仁、兴义东汉墓出土。铜马系分段铸造，装配而成。全马分头、耳、颈、身躯、尾四肢十一段。除两耳外，其余九段皆砂模空心铸造，装配接头为子母口，由十七个销拴固定。两耳及尾铸成子母口投合后，再涂上一种白色粘合料加以固定。从耳至足通高88厘米。昂首翘尾，左前肢提起，张嘴露齿作嘶鸣状。两耳直立，耳内涂朱。辱涂朱，上唇外残留有涂金痕迹，面具涂金。腹部丰满，臀部方圆，长肢，肘腋开豁，方膝，厚蹄，尾打结，这种分段铸造，镶接成形的铜马，在四川也曾出土过，但不多见。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条