说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 普通不锈钢
1)  common stainless steel
普通不锈钢
1.
This paper attempts to find out basis for the application of duplex stainless steel in the equipment of salt making based on the analysis and comparison of anti - corrosion properties of common stainless steel and duplex stainless steel.
本文就普通不锈钢和双相不锈钢的耐蚀性分析、比较,试图为双相不锈钢在制盐设备中的推广应用找出依据。
2)  Puccinia sorghi
普通锈病
1.
During 2002-2004,a total of 176 maize germplasm were identified for resistance to Puccinia sorghi by using the artificial inoculation method in field.
2002~2004年,在田间应用人工喷雾接种的方法对176份玉米种质资源进行苗期抗玉米普通锈病(Puccinia sorghi Schw。
3)  Austnite stainless steel tee joint
奥氏体不锈钢三通
4)  stainless steel
不锈钢
1.
Vacuum hot roll bonding of TC4 titanium alloy and 0Cr18Ni10Ti stainless steel;
TC4钛合金与0Cr18Ni10Ti不锈钢真空热轧连接
2.
Research on cyclic ion nitriding technology catalyzed by rare earth for 2Cr13 stainless steel;
2Cr13不锈钢的稀土催渗循环离子渗氮工艺研究
3.
Analysis of the components of acid chemical coloring solutions for stainless steel;
不锈钢酸性化学着色液成分的分析方法
5)  2Cr13 stainless steel
2Cr13不锈钢
1.
Influence of the TiN film layer on the anti-erosion performance of the 2Cr13 stainless steel blade
TiN膜层提高2Cr13不锈钢叶片的抗冲刷腐蚀性能
2.
Study of hot deformation microstructure and properties for 2Cr13 stainless steel containing rare earth Y
含稀土元素Y的2Cr13不锈钢热变形组织与性能研究
3.
Effect of tempering temperature on stress-corrosion cracking and mechanical hysteresis of 2Cr13 stainless steel
回火温度对2Cr13不锈钢应力腐蚀开裂和力学滞后的影响
6)  1Cr13 stainless steel
1Cr13不锈钢
1.
Vacuum brazing between TiC/NiCr cermets and 1Cr13 stainless steel;
TiC/NiCr金属陶瓷与1Cr13不锈钢的真空钎焊
2.
Titanium coating had been deposited on 1Cr13 stainless steel substrate using cold spray technique.
0MPa,载气温度为500℃的状态下,用冷喷涂的方法在1Cr13不锈钢基体上制备了钛金属涂层。
3.
TiC/Ti(C, N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C, N)/TiN coatings are investigated and studied contrastively from 25℃ to 400℃ in the gross slip regime.
采用化学气相沉积(CVD)技术,在1Cr13不锈钢基体上制备TiC/Ti(C,N)/TiN复合涂层。
补充资料:316L不锈钢纤维


316L不锈钢纤维


一噢撒 乙}6L不锈钢纤维
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条