1) In_2O_3/Al_2O_3
In2O3/Al2O3
1.
The Selective Catalytic Reduction of NO by Propene on In_2O_3/Al_2O_3 Catalysts in the Presence of Oxygen;
采用溶胶-凝胶法制备了In2O3/Al2O3氧化物催化剂,对其进行了BET、XRD、XPS及TPD表征。
2) In_2O_3
In2O3
1.
In_2O_3 nanocones have been in-situ grown on the surface of indium substrates by heating indium grains coated with an Au film at 900～1000 ℃ in air.
以Au作催化剂,将金属铟在空气中加热到900~1 000℃,在单质铟表面制备出In2O3纳米锥。
2.
The In_2O_3 coating by precipitation method to the phosphor was applied to promote the conductivity of particles.
采用高温固相法合成了FED用Y2O3∶Eu红色荧光粉,为提高其导电性,采用表面成膜包覆法对其进行了In2O3包膜研究。
3.
The precursors of In_2O_3 nanorods were prepared by sol-gel technology with the non-ionic surface active agent controlling their morphology.
以非离子表面活性剂作为形貌控制剂,采用溶胶-凝胶法制备In2O3纳米棒前驱物,经500℃煅烧1h,成功制备了长约120nm,直径20nm的In2O3纳米棒。
3) CaO-In_2O_3
CaO-In2O3
1.
Preparation,Structure Attribute And Gas Sensitivity Of CaO-In_2O_3;
采用共沉淀方法,以一定摩尔比的可溶性钙盐和铟盐为源物质,以氢氧化物作为沉淀剂,制备出了CaO-In2O3复合氧化物粉末。
4) indium oxide leyers
In2O3膜
5) Al_2O_3
Al2O3
1.
The Fe-matrix composites reinforced with Al_2O_3were fabricated by melting-casting.
采用熔铸法成功的制备成了Al2O3/Fe复合材料,利用扫描电子显微镜(SEM),来观察增强相Al2O3的微观组织。
2.
The phase transformation of γ-Al_2O_3 at high temperature was characterized by Raman techniques.
通过不同波长的Raman激发光对γ-Al2O3的高温相变过程进行了研究。
3.
Steric hindrance layer can be established when the surfaces of nano-Al_2O_3 were grafted with polyacetal,which(increased) the dispersibility of the nano-particles as well as the compatibility between the particles and the resin matrix.
在纳米Al2O3表面接枝聚缩醛可在粒子表面建立起空间位阻稳定层,不但提高了纳米粒子的分散稳定性,还可以增强纳米粒子与树脂基体的相容性。
6) aluminum oxide
Al2O3
1.
A method was developed for synthesis of DBP catalyzed with non-proton acid and the result showed that aluminum oxide can be used to synthesize dibutyl phthalate characterized with high reaction activity,good selectivity and high rate of conversion,but less environmental pollution.
实验结果表明,Al2O3催化酯化合成邻苯二甲酸二丁酯具有反应时间短、反应活性和选择性好、产率高、无环境污染等优点、是理想的合成DBP的催化剂。
2.
On the basis of wear resistance research on polyurethane matrix composites reinforced with aluminum oxide particles, component of slurry pump coated by the composites with optimum proportion was manufactured.
在Al2O3颗粒增强聚氨酯基复合材料耐磨性的研究基础上,采用具有最佳耐磨性的复合材料配方,进行了砂浆泵护板涂覆及产品实用性研究。
3.
In this paper, the preparation of TiO_2 photocatalyst coated on the aluminum oxide surface by sol-gel technique using tetrabutyl titanate as material was studied.
以钛酸四丁酯为原料,Al2O3为载体,用溶胶-凝胶法制备负载型TiO2,在UV-TiO2体系中对吡啶(PD)进行光催化降解,并研究了将TiO2负载在不同铝源所制备的Al2O3后光催化剂的差异,结果表明:负载型TiO2光催化剂加入量为10mg/40mL,吡啶的光催化降解反应符合一级动力学方程;吡啶中氮转化成氨氮。
补充资料：(E)-2-Hepten-1-al
CAS: 18829-55-5
分子式: C7H12O
分子量: 112.17
沸点: 90-91℃
中文名称: E-2-庚烯醛
分子式: C7H12O
分子量: 112.17
沸点: 90-91℃
中文名称: E-2-庚烯醛
英文名称: (E)-2-Heptenal；(E)-2-Hepten-1-al；(e)-2-heptena；3-butylacrolein；beta-butylacrolein；trans-2-heptenal
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条