1)  stainless plate
不锈钢中板
2)  stainless
不锈
1.
To set forth using circumstance, type number comparison, corrosion type and anti-corrosion capability, process 6f stainless well-measuring steel wire and compare lots of data.
通过对不锈录井钢丝的使用环境、国内外牌号对比、腐蚀类型及其耐蚀能力、工艺等的叙述和大量数据的对照,提出选用不锈录井钢丝的经验公式和选择要求,指导不锈录井钢丝的生产、选用。
3)  stainless steel
不锈钢
1.
Vacuum hot roll bonding of TC4 titanium alloy and 0Cr18Ni10Ti stainless steel;
TC4钛合金与0Cr18Ni10Ti不锈钢真空热轧连接
2.
Research on cyclic ion nitriding technology catalyzed by rare earth for 2Cr13 stainless steel;
2Cr13不锈钢的稀土催渗循环离子渗氮工艺研究
3.
Analysis of the components of acid chemical coloring solutions for stainless steel;
不锈钢酸性化学着色液成分的分析方法
4)  2Cr13 stainless steel
2Cr13不锈钢
1.
The study showed that heat transfer performance of mold fluxes for 2Cr13 stainless steel.
采用DIL402C热膨胀分析仪、STA449C同步热分析仪和Gleeble—1500D热模拟试验机,分别测试2Cr13不锈钢的线性膨胀系数、主要相变温度以及高温力学性能等高温特性,分析2Cr13不锈钢高温性能对铸坯表面质量的影响和铸坯表面凹陷以及微裂纹产生的机理,确定2Cr13不锈钢用保护渣应重点考虑传热性能。
2.
2Cr13 stainless steel was quenched in water and the influence of quenching temperature on microstructre and performance was studied.
对2Cr13不锈钢进行水淬火实验,研究了淬火温度对2Cr13不锈钢组织和性能之间的关系,发现在1050℃淬火时,试样的硬度值基本达到了最高,其原因是因为碳化物大多被溶解,铁素体的含量已经非常低。
3.
Surface modification of 2Cr13 stainless steel was carried out using plasma immersion ion implantation (PIII) combined with ion beam enhanced deposition (IBED) technique.
对 2Cr13不锈钢表面进行了等离子体浸没离子注入(PIII)与离子束增强沉积(IBED)复合强化处理。
5)  1Cr13 stainless steel
1Cr13不锈钢
1.
Vacuum brazing between TiC/NiCr cermets and 1Cr13 stainless steel;
TiC/NiCr金属陶瓷与1Cr13不锈钢的真空钎焊
2.
Titanium coating had been deposited on 1Cr13 stainless steel substrate using cold spray technique.
0MPa,载气温度为500℃的状态下,用冷喷涂的方法在1Cr13不锈钢基体上制备了钛金属涂层。
3.
TiC/Ti(C, N)/TiN multi-layer coatings are prepared on the 1Cr13 stainless steel substrate by the technique of Chemical Vapour Deposition, and the fretting wear behaviour of 1Cr13 stainless steel and TiC/Ti(C, N)/TiN coatings are investigated and studied contrastively from 25℃ to 400℃ in the gross slip regime.
采用化学气相沉积(CVD)技术,在1Cr13不锈钢基体上制备TiC/Ti(C,N)/TiN复合涂层。
6)  254SMo stainless steel
254SMo不锈钢
参考词条
补充资料：不锈钢板
分子式：
分子量：
CAS号：

性质：按制法分热轧和冷轧的两种，包括厚度0.5-4毫米的薄板和4.5-35毫米的厚板。按钢种的组织特征分为5类：奥氏体型、奥氏体-铁素体型、铁素体型、马氏体型、沉淀硬化型。要求能承受草酸、硫酸-硫酸铁、硝酸、硝酸-氢氟酸、硫酸-硫酸铜、磷酸、甲酸、乙酸等各种酸的腐蚀，广泛用于化工、食品、医药、造纸、石油、原子能等工业，以及建筑、厨具、餐具 、车辆、家用电器各类零部件。为了保证各类不锈钢板的屈服强度、抗拉强度、伸长率和硬度等力学性能符合要求，钢板交货前必须经过退火、固溶处理、时效处理等热处理。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。