1) warm drawing
温引伸
1.
At the basis of simulation results,the influences of drawing angle,billet temperature,friction coefficient between female die,punch and workpiece on the warm drawing of cup has been analyzed.
用 MARC/AutoForge 软件对弹体温引伸工艺进行了数值模拟,分析了凹模锥角、坯料温度及凸、凹模与工件之间磨擦系数对引伸工艺的影响,为弹体温引伸工艺制定提供了依据。
2) high-temperature extensometer
高温引伸计
3) drawing
[英]['drɔ:ɪŋ] [美]['drɔ·ɪŋ]
引伸
1.
Study on Spinning-drawing Equipment for Deep Tube;
深筒形件旋压引伸设备的研究
2.
The study on the drawing mould vibration and the numerical simulation of forming precision;
引伸模的振动分析及成形精度的数值模拟
3.
Study on the Rolling-Drawing Compound Forming Process;
辊压引伸复合成形工艺研究
4) ironing
[英]['aɪənɪŋ] [美]['aɪɚnɪŋ]
引伸
1.
But the strength of the cartridge case after ironing drawing cannot be accurately calculated by this formula,because the result of calculation is lower than that reached in practice.
用常规的幂强化公式计算药筒在引伸后的强度时，数值偏低较多，原因是该公式未考虑引伸凹模锥角对强化的影响。
5) stretching of attenuation
变薄引伸
6) Extensometer
[英][,eksten'sɔmitə] [美][,ɛkstɛn'sɑmətɚ]
引伸仪
1.
This paper introduces the method in measuring the elastic modulus E of Epon photoelas-tic materials by means of the electrical measurement at normal temperatures and comparesthe method with the levev extensometer.
本文介绍常温下用电测法测环氧树脂光弹性材料弹性模量E的方法，并与杠杆引伸仪法做了比较。
2.
A new type of extensometer for low temperature is designed and the working principle and technical charac-teristic of it is introduced,meanwhile,the force-displacement curve of a round-bar made of16MnR steel is tested at-196℃.
设计了一种新型低温引伸仪,介绍了其工作原理、技术特点,并采用此引伸仪测试了16MnR钢圆棒试样-196℃下的拉力-位移曲线。
补充资料：婆罗门引 重阳与元帅窦子温暨众友东城赏菊
【诗文】：
浮空霁色，江涵秋影雁初飞。相逢共绕东篱。点检尊前见在，人似晓星稀。对满山红树，叶叶堪题。大家露顶，任短发、被风吹。只恐黄花人貌，不似年时。杯添野水，更何用、频频望白衣。沈醉後，携手方归。
【注释】：
【出处】：
浮空霁色，江涵秋影雁初飞。相逢共绕东篱。点检尊前见在，人似晓星稀。对满山红树，叶叶堪题。大家露顶，任短发、被风吹。只恐黄花人貌，不似年时。杯添野水，更何用、频频望白衣。沈醉後，携手方归。
【注释】：
【出处】：
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条