2) wet film thickner
湿膜厚度计
3) lubricant film thickness
油膜厚度
1.
This paper had got overall introduction on many measurement technologies and detecting methods of lubricant film thickness, and on their disadvantages and application status in that of thrust bearing.
较为全面、系统地介绍了润滑油膜的测量技术和各种检测方法的特点与不足,以及在推力轴承检测中的应用情况,这对于更好地进行推力轴承油膜厚度的检测有一定的参考价值。
4) oil film thickness
油膜厚度
1.
The influence of oil film thickness variation on workpiece gauge control in rolling process is analyzed.
分析了轧制过程油膜厚度变化对钢板厚度控制精度的影响,基于油膜厚度Reynolds计算公式,借鉴轧辊调零计算轧机弹跳的想法,提出相对油膜厚度的计算方法,并在轧机上进行数据采集,得到油膜变化的实测值,通过弹跳曲线的平移处理,得到最终的油膜变化曲线,根据该曲线可很方便地确定模型的结构并拟合出模型系数。
2.
In order to analyze the influence of oil film thickness of back-up roll dynamic oil film bearing in tandem cold rolling on strip thickness and to improve the AGC accuracy,oil film thickness experiment was done.
为了分析冷连轧机支撑辊动压油膜轴承的油膜厚度变化对带钢厚度的影响,提高轧机AGC精度,进行了油膜厚度测试实验。
3.
The hydrostatic slide’s principle,characteristic,classification,applicable situation were introduced,and the effect factors for slide design ,including load capacity,oil film rigidity,oil film thickness as well as slide clearance were analyzed.
介绍了液体静压导轨工作原理、特点、分类及适用场合 ,分析了承载能力、油膜刚度、油膜厚度以及导轨间隙等静压导轨设计的影响因素。
6) film thickness
漆膜厚度
1.
The significance of film thickness control during spraying by robot,influence factors thereof and adjustment of relevant parameters are discussed.
讨论了机器人喷涂涂料时,漆膜厚度控制的意义、影响漆膜厚度的因素以及相应参数的调整方法。
2.
Illstrating the importance of painting to product quality,discussing the approach to dertemining product paint consumptim in painting process and consequently determining the most reasonable film thickness to minimize paint consumption ,providing a useful referece for determination of paint consumption for similar products in painting process.
阐述了产品油漆对产品质量影响性 ,讨论产品油漆工艺消耗定额的制定方法 ,制定最合理漆膜厚度 ,使油漆消耗量降至最低值 ,为同类产品油漆工艺消耗定额的制定提供了有益的参考。
补充资料：湿膜厚度计
分子式：
CAS号：
性质：在漆膜制备后立即进行测量厚度的仪器。有轮规（wheel tube）和梳规（comb tube）。轮规由三个圆盘组成，外侧两个圆盘在某一半径处相切，该处的间隙为零，在相反关径处，间隔最大，外侧有刻度，指示不同间隙的读数；梳规为一正方形或矩形金属板或塑料片，在其4边都刻着带不同读数的齿，各齿距水平面有依次递升的不同间隙。湿膜厚度为沾湿的轮或齿的读数。
CAS号：
性质：在漆膜制备后立即进行测量厚度的仪器。有轮规（wheel tube）和梳规（comb tube）。轮规由三个圆盘组成，外侧两个圆盘在某一半径处相切，该处的间隙为零，在相反关径处，间隔最大，外侧有刻度，指示不同间隙的读数；梳规为一正方形或矩形金属板或塑料片，在其4边都刻着带不同读数的齿，各齿距水平面有依次递升的不同间隙。湿膜厚度为沾湿的轮或齿的读数。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条