说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 对定误差
1)  error in positioning and tool-setting
对定误差
2)  relative error
相对误差
1.
Linear combination forecast based on relative error criterion;
基于相对误差的线性组合预测研究
2.
The model is used to analyze the relative error of forecast and to forecast the exploitable geological ore reserves of Miaogou Mine in 2007.
通过运用数理统计中的回归分析方法确立采出矿石地质矿量预测数学模型,分析预测相对误差,并对2007年采出矿石地质矿量进行预测。
3.
The calculation methods of pH and relative error were studied in different acid-base solution.
根据相对误差的要求,研究不同酸碱平衡溶液中pH值的计算方法,并根据酸碱的强弱和浓度及离解常数的大小,进行近似处理,可得到简便计算pH值的公式。
3)  absolute error
绝对误差
1.
By comparison with the results of ideal Henon sequence mixed with noise,the improved Farmer algorithm is able to increase the precision of noise attenuation and reduce the absolute error between itself and ideal Henon sequ.
通过对混有噪声的Henon序列进行仿真实验,仿真结果显示,改进后的Farm er算法能够提高噪声衰减的精度,降低与理想Henon序列的绝对误差。
2.
According to original laser measure error and error analysis transfer expressions,calculations about absolute errors and relative errors of the measuring deformation of wing were performed.
以激光器的原始测距误差为出发点,依据误差传递公式,分析了测量机翼变形量的绝对误差和相对误差,并给出了计算仿真结果和相应的图形。
3.
It may measure the frequency and phase of the signal which begin from 10 Hz to 20 kHz,absolute error isn′t more than 1°.
可以对10 Hz~2 0 k Hz频率范围的信号进行频率、相位等参数的精确测量,测相绝对误差不大于1°;采用数码管显示被测信号的频率、相位差。
4)  tool clamping error
对刀误差
1.
Based on the analysis of the influence of actual distribution of manufacturing deviation and fit-up gap on tool clamping error of driller clamping fixture, the analytic method about the tool clamping error is put forward.
通过分析钻床夹具制造偏差的实际分布状态与装配间隙 (过盈为非间隙 )对对刀误差的影响 ,提出了对刀误差的实态分析计算方法。
5)  Alignment Error
对准误差
1.
The Hazard and It's Correcting Methods of Alignment Error between Tool-tip and Spindle Center of NC Lathe;
数控车床刀尖与主轴中心对准误差的危害及纠正方法
2.
Observability and alignment error analysis for rapid transfer alignment of inertial navigation system;
惯导快速传递对准的可观测性和对准误差分析
3.
Analysis of system servo following error caused by alignment error of ESG;
静电陀螺仪对准误差产生的系统伺服随动误差分析
6)  shaft alignment
对中误差
1.
It pointed out the errors formed by the two randomness and illustrated the faults of the four parameters system which is used in describing the shaft alignment error of a coupling by abroad technician.
分析了机器安装过程中联轴器两轴线的公垂线与联轴器中心的相对位置关系的随机性及机器地脚支承面方位的随机性,指出了两种随机性所产生的误差,说明了国外工程界在描述联轴器对中误差时所用的4参数体系存在的不足。
补充资料:皮米诺定 ,去痛定,匹米诺定
药物名称:匹米诺定

英文名:Piminodine

别名: 皮米诺定 ,去痛定,匹米诺定
外文名:Piminodine
适应症: 为强效麻醉性镇痛药,镇痛作用较呱替啶强。用于胆囊炎合并胆结石、胰腺炎、癌症等引起的剧痛。
用量用法: 1.皮下注射或肌注:1次10~20mg,必要时每4小时1次。 2.口服:1次25~50mg。
注意事项: 有成瘾性。
规格: 1.片剂:25mg。 2.注射液:10mg。





类别:镇痛药\阿片受体激动药
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条