1) conical parts
圆锥形件
1.
Doing simulation and experiments of drawing process for conical partsAcquiring displacement、stress and strain fields during drawing process for conical parts.
对圆锥形件的拉深过程进行了数值模拟和实验验证。
2) conical part
圆锥形件
1.
Development of intellectual system for conical part deep drawing;
圆锥形件智能拉深实验系统的研究
2.
This paper had analyzed the deformation feature and essence of conical part in main deformation region (the side\|wall of hang in the air section).
在跟踪金属质点位移轨迹的基础上 ,揭示了毛坯变形区各质点贴模位移与应变间的关系 ,从而明确提出了圆锥形件的成形机理。
3.
A mechanical model of conical part stamping process is built under the conditions of considering thickness variation,anisotropy,work\|hardening,friction factor and so on.
在综合考虑板厚变化、各向异性、加工硬化及摩擦等因素的情况下 ,建立了圆锥形件冲压成形过程的力学模型。
3) conical part
圆锥形零件
1.
Hydraulic counter pressure drawing is one of newstamping technology, research by numerical simulation onconical part deep drawing with hydraulic counter pressure ispresented.
充液拉深是一种板料冲压成形新工艺，本文用ＭＡＲＣ软件对圆锥形零件充液拉深过程进行了数值模拟。
2.
Therefore it is necessary to study forming characteristic of conical part, to analyze various parameters'influence on its forming limit, and to define reasonable blank holding force(BHF).
圆锥形零件是曲面类零件中较为典型的零件，对其冲压成形过程的研究是进行曲面类零件研究的基础。
4) cone-shaped and thin-walled part
圆锥形薄壁件
1.
The forming process of the cone-shaped and thin-walled part is simulated by means of forming FEA software ANSYS in this article.
采用了ANSYS有限元分析软件对圆锥形薄壁件成形过程进行了数值模拟,分析了冲压过程中两类失效形式产生的原因,并提出了相应的解决办法。
5) the long conical pipe
深圆锥形管件
1.
Generally, the technique of extruding the long conical pipe whose relative height is 5~12 is very hard.
采用冷挤压成形工艺方法,能生产出各种尺寸、规格的深圆锥形管件。
6) spherical-bottomed conical bodies
球底圆锥形件
1.
Forming limit of spherical-bottomed conical bodies;
球底圆锥形件拉深成形极限研究
补充资料：Z型圆锥形橡胶减震器
分子式：
CAS号：
性质： 橡胶减震器的一种。外形呈圆锥形。由上下两个倒喇叭形金属骨架中间夹橡胶模压而成。产品三向等频，大变形，结构紧凑，质量轻。用于各种机械、仪表、机床、设备等方面。
CAS号：
性质： 橡胶减震器的一种。外形呈圆锥形。由上下两个倒喇叭形金属骨架中间夹橡胶模压而成。产品三向等频，大变形，结构紧凑，质量轻。用于各种机械、仪表、机床、设备等方面。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条