1) alumina matrix ceramic
氧化铝基陶瓷材料
1.
This article compared the wear behaviors of the alumina matrix ceramic with that of the steel bonded carbide GT35 without lubricant and analyzed the wear mechanism of the both materials.
测定了无润滑条件下氧化铝基陶瓷材料与钢结硬质合金GT35的摩擦磨损特性,并对磨损机理作了对比分析。
3) Al_2O_3 slurry
氧化铝陶瓷料浆
1.
When the content of talc was less than 4wt% , the viscosity of Al_2O_3 slurry increased slightly with an increase in talc content.
通过流变实验分析了滑石含量及球磨工艺对水基氧化铝陶瓷料浆流变性的影响。
4) silicon carbide whisker reinforced alumina ceramic composite
碳化硅晶须补强氧化铝陶瓷基复合材料
5) alumina matrix ceramics
氧化铝基陶瓷
1.
Fracture toughness of alumina matrix ceramics measured by indentation method and single edge notched beam specimen techniques were analyzed and contrasted, and the most suitable indentation method equation was confirmed.
用压痕法和单边切口梁法测量了氧化铝基陶瓷材料的断裂韧性,对这两种方法所测得的结果进行了分析对比,确定了最适用的压痕法计算公式。
2.
The effects of CeO2 on sintering,mechanical properties and thermal shock resistance of alumina matrix ceramics were studied in this paper.
通过适当工艺制备出了添加不同含量CeO2(0～2wt%)的氧化铝基陶瓷,研究了CeO2对氧化铝基陶瓷的烧结性、力学性能和抗热震性的影响。
6) Al2O3-based ceramics
氧化铝基陶瓷
1.
The state of investigation on thermal shock resistance of Al2O3-based ceramics at home and abroad in recent years and the theories of ceramic thermal resistance were briefly described,and the progress of investigation in thermal shock resistance of Al2O3-based ceramics and several approaches to improve the thermal shock resistance of Al2O3-based ceramics were summarized.
根据近年来国内外氧化铝基陶瓷抗热震性的研究现状,简要地介绍了抗热震陶瓷的评价理论,系统总结了氧化铝基陶瓷材料抗热震性的有关研究进展情况以及目前提高氧化铝基陶瓷抗热震性的几种途径。
补充资料：碳化硅晶须补强氧化铝陶瓷基复合材料
分子式：
CAS号：
性质：以氧化铝陶瓷为基体由碳化硅增强的复合材料。氧化铝陶瓷硬度大，熔点高，但强度和断裂韧性低。采用热压烧结法制备出的复合材料，抗弯强度可达600～900MPa，断裂韧性达7～9MPa。m1/2。同时还具有良好高温性能。用在刀具、陶瓷发动机和航天航空等方面。
CAS号：
性质：以氧化铝陶瓷为基体由碳化硅增强的复合材料。氧化铝陶瓷硬度大，熔点高，但强度和断裂韧性低。采用热压烧结法制备出的复合材料，抗弯强度可达600～900MPa，断裂韧性达7～9MPa。m1/2。同时还具有良好高温性能。用在刀具、陶瓷发动机和航天航空等方面。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条