1) Fe_2TiP precipitate
析出物Fe2TiP
2) sludge analysis
析出物分析
3) precipitates
[英][pri'sipitit] [美][prɪ'sɪpətɪt]
析出物
1.
Effect of Deforming Temperature on Structure and Precipitates of 0.05C-0.13Nb Steel;
变形温度对0.05C-0.13Nb钢组织和析出物的影响
2.
The mechanical property of steel Q345B at elevated temperature is tested and the type of the precipitates existing at the cracks is identified and thereupon cause to formation of the corner cracks is analyzed and the processing measures to eliminate the defect accordingly is put forward.
测试了Q345B钢的高温力学性能,鉴别了铸坯裂纹处析出物的类型,在此基础上分析了连铸坯角裂形成原因,并提出了消除角裂的工艺措施。
3.
The precipitates in hot rolled strip of two grades of non-oriented electrical steel(W540,W800) produced by CSP process and one grade of non-oriented electrical steel(W20) produced by conventional process were investigated.
对CSP流程生产的W540和W800两个牌号的无取向电工钢热轧板中析出物尺寸在卷取前后的变化进行了研究,并和传统流程生产的W20热轧板的析出物进行了比较。
4) precipitate
[英][pri'sipiteit] [美][prɪ'sɪpɪ,tet]
析出物
1.
For a kind of low carbon micro-alloyed steel,a thermal simulation test was conducted with samples of F+B+P microstructure and the effects of its cold deformation at room temperature on the distribution,size and composition of precipitates were investigated via a technological process for rapid heating and short holding time.
以一种低碳微合金钢为对象,通过热模拟实验研究了室温变形对最终组织中析出物的分布、尺寸以及成分等的影响。
2.
The inclusion and precipitate of Ti and Nb microalloy Q345B heavy plate are observed and analyzed by electron probe and transmission electron microscope (TEM).
用电子探针和透射电镜对厚规格Ti、Nb微合金化Q345B钢板中夹杂物和析出物进行了观察分析,结果表明,Q345B钢板中的夹杂物主要是锰、钙的氧化物和硫化物以及它们的复合夹杂物,氧化物大多呈球状或椭球状,硫化物多数呈长条状;析出物主要是铌和钛及其化合物,钛主要以TiN的形式存在,呈方形或矩形;铌主要以尺寸较大的碳氮化物存在,以椭圆形为主,析出在奥氏体晶内、晶界上。
3.
Grain refinement turn out in the alloy and a few minor precipitates also appear after annealing.
用金相显微镜、扫描电镜观察合金铸态以及退火态的组织,有明显的晶粒细化现象以及细小的析出物出现。
5) MX precipitation
MX析出物
6) deposition
[英][,depə'zɪʃn] [美]['dɛpə'zɪʃən]
析出物
1.
Effect of deposition on the tensile strength of tungsten alloy;
析出物对93WNiFe合金抗拉强度的影响
2.
Study on Preparation of Standard Sample of Deposition in Steel;
不锈钢中析出物标准样品的研制
补充资料：crack tip opening displacement
分子式：
CAS号：
性质：在外载荷的作用下，裂纹尖端两表面间的张开位移。用符号δ表示。由于在弹塑性条件下，已得到δ与工作应力σ(或应变ε)以及裂纹尺寸a(裂纹的半长)之间的关系，因此它是弹塑性断裂力学中的一个重要参量。
CAS号：
性质：在外载荷的作用下，裂纹尖端两表面间的张开位移。用符号δ表示。由于在弹塑性条件下，已得到δ与工作应力σ(或应变ε)以及裂纹尺寸a(裂纹的半长)之间的关系，因此它是弹塑性断裂力学中的一个重要参量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条